EZHome V4.1

This is based on Tasmota V14.4.1 for the EZPlug V2 ONLY.

This release ONLY supports the EZPlug V2 plugs at this time.

REMOVE OTA FIRMWARE MENU.
WILL REVISIT OTA FROM GITHUB RELEASES AT LATER TIME

EZHome V4.0

This is based on Tasmota V14.4.1 for the EZPlug V2 ONLY.

This release ONLY supports the EZPlug V2 plugs at this time.

DO NOT USE THE OTA UPDATE IN THE FIRMWARE. ALWAYS MANUALLY UPDATE FROM THIS GITHUB REPO.

EZHome V3.0

Updates

Updated to Tasmota V13.2.0.
Tested on all EZHome Devices

Disabled MQTT Host Discovery as Tasmota team states this can cause high load and delays on tasmota devices.

Removed Flood Bulbs as they never were released.

OTA Update Notes

If updating from the OTA server listed in the plug does not work then manually download the file for your plug or bulb and upload it manually.

Power Calibration Info

Due to manufacturing variances the plug info may still be slightly off, this is normal.

If you want to get it exact for your power and particular setup you can always calibrate with the Tasmota Power Calibration guide.

Readme before upgrading

If on version V2.0 or higher, just install the firmware via the web GUI.

On a version older than V2.0? Upgrade to EZHome V1.0 before updating to this V3.0 release.

Then update to this release after you issue the Reset 4 option in the console as detailed below.

If coming from V2.0 you can upgrade in place. To get the new power calibration settings for the EZPlug plus use the Reset 4 option in the console as detailed in the V1.0 release notes.

Restore Firmware Defaults w/Keeping Wifi

We recommend resetting the firmware to defaults after installing this update. If you do not some backend settings and the OTA URL will not be correct when coming from our older firmware for the EZHome products.

To do this bring up the web interface for your device and then click the Console button.

In the console type Reset 4 and press enter. This will reset the device to defaults but still retain your wifi information.

EZHome V2.1

Updates

Updated power calibration settings for Tasmota 11.0.0 for EZPlug Plus.
Updated footer to show EZHome version and Tasmota version for easier identification.

This update addresses power calibration being off for the EZPlug Plus for some units. If you do not have an EZPlug Plus you can skip this update.

OTA Update Notes

If updating from the OTA server listed in the plug does not work then manually download the file for your plug or bulb and upload it manually.

Power Calibration Info

Due to manufacturing variances the plug info may still be slightly off, this is normal.

If you want to get it exact for your power and particular setup you can always calibrate with the Tasmota Power Calibration guide.

Readme before upgrading

Upgrade to EZHome V1.0 before updating to this V2.1 release.

Then update to this release after you issue the Reset 4 option in the console as detailed below.

If coming from V2.0 you can upgrade in place. To get the new power calibration settings for the EZPlug plus use the Reset 4 option in the console as detailed in the V1.0 release notes.

Restore Firmware Defaults w/Keeping Wifi

We recommend resetting the firmware to defaults after installing this update. If you do not some backend settings and the OTA URL will not be correct when coming from our older firmware for the EZHome products.

To do this bring up the web interface for your device and then click the Console button.

In the console type Reset 4 and press enter. This will reset the device to defaults but still retain your wifi information.

EZHome V2.0

Updates

Updated to Tasmota 11.0.0 Code base.

OTA Update Notes

If updating from the OTA server listed in the plug does not work then manually download the file for your plug or bulb and upload it manually.

Readme before upgrading

Upgrade to EZHome V1.0 before updating to this V2.0 release.

Then update to this release after you issue the Reset 4 option in the console as detailed below.

Restore Firmware Defaults w/Keeping Wifi

We recommend resetting the firmware to defaults after installing this update. If you do not some backend settings and the OTA URL will not be correct when coming from our older firmware for the EZHome products.

To do this bring up the web interface for your device and then click the Console button.

In the console type Reset 4 and press enter. This will reset the device to defaults but still retain your wifi information.

EZHome V1.0

Changes

• Updated code to Tasmota 10.1.0 Base
• Added Support for EZBulb V1 Product
• Renamed from EZPlug to EZHome for Repo Name
• Added binary files for all products
• Added compile/test tools

Updating

These new builds are small enough to directly flash onto existing devices without using a "minimal" build as in the past. Once you are on this version you will be able to use the built-in OTA upgrade from the device web UI going forward. Make sure to reset the firmware to defaults using the details below.

OTA Update Notes

If updating from the OTA server listed in the plug does not work then manually download the file for your plug or bulb and upload it manually.

Don't have the "Upgrade by web server" option?

You can download the XXX.bin.gz file from the release page and upload it to your device. Make sure to get the correct file for your device (aka EZPlug vs EzPlugPlus). You can then upload the file to the device and then click start upgrade. It will upload and then restart.

Have the "Upgrade by web server" option?

Some older EZPlugs will have the "Upgrade by web server" option but it defaults to the Tasmota URL. Paste in the URL for your device below and then click Start Upgrade.

• EZPlug: https://github.com/th3dstudio/EZHome/releases/latest/download/EZPlug.bin.gz
• EZPlug+: https://github.com/th3dstudio/EZHome/releases/latest/download/EZPlugPlus.bin.gz
• EZBulb: https://github.com/th3dstudio/EZHome/releases/latest/download/EZBulb.bin.gz

Restore Firmware Defaults w/Keeping Wifi

We recommend resetting the firmware to defaults after installing this update. If you do not some backend settings and the OTA URL will not be correct when coming from our older firmware for the EZHome products.

To do this bring up the web interface for your device and then click the Console button.

In the console type Reset 4 and press enter. This will reset the device to defaults but still retain your wifi information.

EZPlug 082721 Release

Updating your EZPlug Firmware

• Download the latest releases for your plug (EZPlug or EZPlug+).
  • You will need the normal (the one WITHOUT minimal in the name) BIN file and the minimal (the one WITH minimal in the name) BIN file
• Flash the minimal BIN file from the GUI
• Flash the normal BIN file from the GUI
• Enjoy the updated firmware

If you are re-flashing because you hit the 'Update Firmware' from the stock Tasmota URL it is recommended to perform a "Reset Configuration" after reflashing to our firmware.

---

Changelog

• Updated to Tasmota 9.5.0 Release Code
• WEMO emulation is on by default now.
• Flashing from 8.5.1 to 9.5.0 is supported.
• Removed OTA Upload to Prevent Users from pulling standard Tasmota builds.
• Added EZPlug release link on firmware page
• Updated footer to TH3D info

EZPlug 102020 Release

Initial Release based on Tasmota 8.5.1 Release
This is the firmware the plugs ship with as of 10/20/2020. Plugs ship with the EZPlug_102020.bin file (EZPlug) or EZPlug_Plus_102020.bin file (EZPlug+).

Bin files with "WEmu" in the name have Wemo and Hue Emulation feature in them.

Updating your EZPlug Firmware

• Download the latest releases for your plug (EZPlug or EZPlug+). You will need the normal BIN file and the minimal BIN file
• Flash the minimal BIN file from the GUI
• Flash the normal BIN file from the GUI
• Enjoy the updated firmware

If you are re-flashing because you hit the 'Update Firmware' from the stock Tasmota URL it is recommended to perform a "Reset Configuration" after reflashing to our firmware.