Add PowerWalker VFI 2000 CRM LCD dump

PowerWalker/PowerWalker__VFI_2000_CRM_LCD__nutdrv_qx__2.8.1__01.dev

@@ -0,0 +1,165 @@
+# Please add if relevant: DEVICE:URL:REPORT: https://github.com/networkupstools/nut/issues/3333
+# Please add if relevant: DEVICE:URL:VENDOR: https://powerwalker.com/de/produkt/10122001/
+
+# DEVICE:COMMENT:
+# Device dump generated by dump.sh on Sat, 28 Feb 2026 14:42:18 +0000
+# PowerWalker VFI 2000 CRM LCD
+# DEVICE:EOC
+
+# :; upsc powerwalker
+battery.charge: 98
+battery.energysave: no
+battery.packs: 1
+battery.protection: yes
+battery.runtime: 1920
+battery.voltage: 054.5
+battery.voltage.high: 52.00
+battery.voltage.low: 41.60
+battery.voltage.nominal: 48.0
+device.model: WPHVR2K0
+device.type: ups
+driver.debug: 0
+driver.flag.allow_killpower: 0
+driver.name: nutdrv_qx
+driver.parameter.pollfreq: 30
+driver.parameter.pollinterval: 1
+driver.parameter.port: auto
+driver.parameter.productid: 5161
+driver.parameter.synchronous: auto
+driver.parameter.vendorid: 0665
+driver.state: quiet
+driver.version: 2.8.1
+driver.version.data: Voltronic 0.08
+driver.version.internal: 0.36
+driver.version.usb: libusb-1.0.27 (API: 0x100010a)
+input.frequency: 50.0
+input.frequency.high: 53.0
+input.frequency.low: 47.0
+input.frequency.nominal: 50.0
+input.phases: 1
+input.transfer.high: 242
+input.transfer.high.max: 254
+input.transfer.high.min: 237
+input.transfer.low: 218
+input.transfer.low.max: 223
+input.transfer.low.min: 206
+input.voltage: 236.2
+input.voltage.nominal: 230.0
+output.current: 1.6
+output.current.nominal: 8
+output.frequency: 50.0
+output.frequency.nominal: 50.0
+output.phases: 1
+output.power.maximum.percent: 19
+output.power.minimum.percent: 21
+output.powerfactor: 0.8
+output.voltage: 230.2
+output.voltage.nominal: 230.0
+ups.beeper.status: enabled
+ups.delay.shutdown: 30
+ups.delay.start: 180
+ups.firmware: 01072.07
+ups.firmware.aux: P01
+ups.load: 22
+ups.power.nominal: 2000
+ups.productid: 5161
+ups.start.auto: yes
+ups.start.battery: yes
+ups.status: OL
+ups.temperature: 27.7
+ups.type: online
+ups.vendorid: 0665
+
+# DEVICE:COMMENT-BLOCK:FIXME:UPSRW: powerwalker
+# [battery.energysave]
+# Switch off when running on battery and no/low load
+# Type: ENUM NUMBER
+# Option: "no" SELECTED
+# Option: "yes"
+#
+# [battery.packs]
+# Number of battery packs
+# Type: RANGE NUMBER
+# Option: "1-99" SELECTED
+#
+# [battery.protection]
+# Prevent deep discharge of battery
+# Type: ENUM NUMBER
+# Option: "no"
+# Option: "yes" SELECTED
+#
+# [driver.debug]
+# Current debug verbosity level of the driver program
+# Type: NUMBER
+# Value: 0
+#
+# [driver.flag.allow_killpower]
+# Safety flip-switch to allow the driver daemon to send UPS shutdown command (accessible via driver.killpower)
+# Type: NUMBER
+# Value: 0
+#
+# [input.frequency.high]
+# Maximum input line frequency (Hz)
+# Type: RANGE NUMBER
+# Option: "53-60" SELECTED
+#
+# [input.frequency.low]
+# Minimum input line frequency (Hz)
+# Type: RANGE NUMBER
+# Option: "40-47" SELECTED
+#
+# [input.transfer.high]
+# High voltage transfer point (V)
+# Type: RANGE NUMBER
+# Option: "237-254" SELECTED
+#
+# [input.transfer.low]
+# Low voltage transfer point (V)
+# Type: RANGE NUMBER
+# Option: "206-223" SELECTED
+#
+# [ups.delay.shutdown]
+# Interval to wait after shutdown with delay command (seconds)
+# Type: RANGE NUMBER
+# Option: "12-5940" SELECTED
+#
+# [ups.delay.start]
+# Interval to wait before (re)starting the load (seconds)
+# Type: RANGE NUMBER
+# Option: "0-599940" SELECTED
+#
+# [ups.start.auto]
+# UPS starts when mains is (re)applied
+# Type: ENUM NUMBER
+# Option: "no"
+# Option: "yes" SELECTED
+#
+# [ups.start.battery]
+# Allow to start UPS from battery
+# Type: ENUM NUMBER
+# Option: "no"
+# Option: "yes" SELECTED
+# DEVICE:EOC
+
+# DEVICE:COMMENT-BLOCK:FIXME:UPSCMD: powerwalker
+# Instant commands supported on UPS [powerwalker]:
+#
+# beeper.disable - Disable the UPS beeper
+# beeper.enable - Enable the UPS beeper
+# beeper.toggle - Toggle the UPS beeper
+# bypass.start - Put the UPS in bypass mode
+# bypass.stop - Take the UPS out of bypass mode
+# driver.killpower - Tell the driver daemon to initiate UPS shutdown; should be unlocked with driver.flag.allow_killpower option or variable setting
+# driver.reload - Reload running driver configuration from the file system (only works for changes in some options)
+# driver.reload-or-error - Reload running driver configuration from the file system (only works for changes in some options); return an error if something changed and could not be applied live (so the caller can restart it with new options)
+# driver.reload-or-exit - Reload running driver configuration from the file system (only works for changes in some options); exit the running driver if something changed and could not be applied live (so service management framework can restart it with new options)
+# load.off - Turn off the load immediately
+# load.on - Turn on the load immediately
+# shutdown.return - Turn off the load and return when power is back
+# shutdown.stayoff - Turn off the load and remain off
+# shutdown.stop - Stop a shutdown in progress
+# test.battery.start - Start a battery test
+# test.battery.start.deep - Start a deep battery test
+# test.battery.start.quick - Start a quick battery test
+# test.battery.stop - Stop the battery test
+# DEVICE:EOC