[PW_SID:1039078] [v2,net-next] net: 6lowpan: replace sprintf() with scnprintf() in debugfs #3250
Conversation
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
…lled up by hw On QCS9075 and QCA8275 platforms, the BT_EN pin is always pulled up by hw and cannot be controlled by the host. As a result, in case of a firmware crash, the host cannot trigger a cold reset. Instead, the BT controller performs a warm restart on its own, without reloading the firmware. This leads to the controller remaining in IBS_WAKE state, while the host expects it to be in sleep mode. The mismatch causes HCI reset commands to time out. Additionally, the driver does not clear internal flags QCA_SSR_TRIGGERED and QCA_IBS_DISABLED, which blocks the reset sequence. If the SSR duration exceeds 2 seconds, the host may enter TX sleep mode due to tx_idle_timeout, further preventing recovery. Also, memcoredump_flag is not cleared, so only the first SSR generates a coredump. Tell the driver that the BT controller has undergone a proper restart sequence: - Clear QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags after SSR. - Add a 50ms delay to allow the controller to complete its warm reset. - Reset tx_idle_timer to prevent the host from entering TX sleep mode. - Clear memcoredump_flag to allow multiple coredump captures. Apply these steps only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set, which indicates that BT_EN is defined in DTS and cannot be toggled. Refer to the comment in include/net/bluetooth/hci.h for details on HCI_QUIRK_NON_PERSISTENT_SETUP. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
MGMT_SETTING_ISO_BROADCASTER and MGMT_SETTING_ISO_RECEIVER flags are missing from supported_settings although they are in current_settings. Report them also in supported_settings to be consistent. Fixes: ae75336 ("Bluetooth: Check for ISO support in controller") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
conn->le_{tx,rx}_phy is not actually a bitfield as it set by
HCI_EV_LE_PHY_UPDATE_COMPLETE it is actually correspond to the current
PHY in use not what is supported by the controller, so this introduces
different fields (conn->le_{tx,rx}_def_phys) to track what PHYs are
supported by the connection.
Fixes: eab2404 ("Bluetooth: Add BT_PHY socket option")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 98921db ("Bluetooth: Use devm_kzalloc in btusb.c file"). In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This ties the lifetime of all the btusb data to the binding of a driver to one interface, INTF. In a driver that binds to other interfaces, ISOC and DIAG, this is an accident waiting to happen. The issue is revealed in btusb_disconnect(), where calling usb_driver_release_interface(&btusb_driver, data->intf) will have devm free the data that is also being used by the other interfaces of the driver that may not be released yet. To fix this, revert the use of devm and go back to freeing memory explicitly. Fixes: 98921db ("Bluetooth: Use devm_kzalloc in btusb.c file") Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for MediaTek7920 0489:e158 /sys/kernel/debug/usb/devices reports for that device: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e158 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Andrew Elatsev <elantsew.andrew@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Switch to the generic PCI power management framework and remove legacy
callbacks like .suspend() and .resume(). With the generic framework, the
standard PCI related work like:
- pci_save/restore_state()
- pci_enable/disable_device()
- pci_set_power_state()
is handled by the PCI core and this driver should implement only
hci_bcm4377 specific operations in its respective callback functions.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This increases build coverage and allows to drop an #ifdef. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_conn_enter_active_mode() uses queue_delayed_work() with the intention that the work will run after the given timeout. However, queue_delayed_work() does nothing if the work is already queued, so depending on the link policy we may end up putting the connection into idle mode every hdev->idle_timeout ms. Use mod_delayed_work() instead so the work is queued if not already queued, and the timeout is updated otherwise. Signed-off-by: Stefan Sørensen <ssorensen@roku.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The connection link policy is only set when establishing an outgoing ACL connection causing connection idle modes not to be available on incoming connections. Move the setting of the link policy to the creation of the connection so all ACL connection will use the link policy set on the HCI device. Signed-off-by: Stefan Sørensen <ssorensen@roku.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
While the configurable system parameters allow controlling the SNIFF mode parameters, they do not include the idle_timeout parameter responsible for enabling SNIFF mode. Add the idle_timeout parameter to allow controlling the idle timeout of BR/EDR connections. Signed-off-by: Stefan Sørensen <ssorensen@roku.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
…ures 1. Implement LE Event Mask to include events required for LE Channel Sounding 2. Enable Channel Sounding feature bit in the LE Host Supported Features command 3. Define HCI command and event structures necessary for LE Channel Sounding functionality Signed-off-by: Naga Bhavani Akella <naga.akella@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables client to use setsockopt(BT_PHY) to set the connection
packet type/PHY:
Example setting BT_PHY_BR_1M_1SLOT:
< HCI Command: Change Conne.. (0x01|0x000f) plen 4
Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
Packet type: 0x331e
2-DH1 may not be used
3-DH1 may not be used
DM1 may be used
DH1 may be used
2-DH3 may not be used
3-DH3 may not be used
2-DH5 may not be used
3-DH5 may not be used
> HCI Event: Command Status (0x0f) plen 4
Change Connection Packet Type (0x01|0x000f) ncmd 1
Status: Success (0x00)
> HCI Event: Connection Packet Typ.. (0x1d) plen 5
Status: Success (0x00)
Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
Packet type: 0x331e
2-DH1 may not be used
3-DH1 may not be used
DM1 may be used
DH1 may be used
2-DH3 may not be used
3-DH3 may not be used
2-DH5 may not be used
Example setting BT_PHY_LE_1M_TX and BT_PHY_LE_1M_RX:
< HCI Command: LE Set PHY (0x08|0x0032) plen 7
Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
All PHYs preference: 0x00
TX PHYs preference: 0x01
LE 1M
RX PHYs preference: 0x01
LE 1M
PHY options preference: Reserved (0x0000)
> HCI Event: Command Status (0x0f) plen 4
LE Set PHY (0x08|0x0032) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 6
LE PHY Update Complete (0x0c)
Status: Success (0x00)
Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
TX PHY: LE 1M (0x01)
RX PHY: LE 1M (0x01)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds workflow files for ci: [sync.yml] - The workflow file for scheduled work - Sync the repo with upstream repo and rebase the workflow branch - Review the patches in the patchwork and creates the PR if needed [ci.yml] - The workflow file for CI tasks - Run CI tests when PR is created Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
sprintf() does not perform bounds checking on the destination buffer. Replace it with scnprintf() to ensure the write stays within bounds. No functional change intended. Signed-off-by: Kathara Sasikumar <katharasasikumar007@gmail.com>
|
CheckPatch |
|
GitLint |
|
SubjectPrefix |
|
BuildKernel |
|
CheckAllWarning |
|
CheckSparse |
|
BuildKernel32 |
|
TestRunnerSetup |
|
TestRunner_l2cap-tester |
|
TestRunner_iso-tester |
|
TestRunner_bnep-tester |
|
TestRunner_mgmt-tester |
|
TestRunner_rfcomm-tester |
|
TestRunner_sco-tester |
|
TestRunner_ioctl-tester |
|
TestRunner_mesh-tester |
|
TestRunner_smp-tester |
|
TestRunner_userchan-tester |
|
IncrementalBuild |
github-actions
bot
force-pushed
the
workflow
branch
4 times, most recently
from
264a7dc to
e7984f7
Compare
github-actions
bot
force-pushed
the
workflow
branch
3 times, most recently
from
afe7dda to
f6b7f11
Compare
github-actions
bot
force-pushed
the
workflow
branch
4 times, most recently
from
b61904b to
21df9a1
Compare
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
sprintf() does not perform bounds checking on the destination buffer.
Replace it with scnprintf() to ensure the write stays within bounds.
No functional change intended.
Signed-off-by: Kathara Sasikumar katharasasikumar007@gmail.com
v2:
net/6lowpan/debugfs.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)