sdkconfig

#
# Automatically generated file. DO NOT EDIT.
# Espressif IoT Development Framework (ESP-IDF) 6.0.0 Project Configuration
#
# default:
CONFIG_SOC_ADC_SUPPORTED=y
# default:
CONFIG_SOC_DEDICATED_GPIO_SUPPORTED=y
# default:
CONFIG_SOC_UART_SUPPORTED=y
# default:
CONFIG_SOC_UHCI_SUPPORTED=y
# default:
CONFIG_SOC_GDMA_SUPPORTED=y
# default:
CONFIG_SOC_AHB_GDMA_SUPPORTED=y
# default:
CONFIG_SOC_GPTIMER_SUPPORTED=y
# default:
CONFIG_SOC_PCNT_SUPPORTED=y
# default:
CONFIG_SOC_MCPWM_SUPPORTED=y
# default:
CONFIG_SOC_TWAI_SUPPORTED=y
# default:
CONFIG_SOC_ETM_SUPPORTED=y
# default:
CONFIG_SOC_PARLIO_SUPPORTED=y
# default:
CONFIG_SOC_BT_SUPPORTED=y
# default:
CONFIG_SOC_IEEE802154_SUPPORTED=y
# default:
CONFIG_SOC_ASYNC_MEMCPY_SUPPORTED=y
# default:
CONFIG_SOC_USB_SERIAL_JTAG_SUPPORTED=y
# default:
CONFIG_SOC_TEMP_SENSOR_SUPPORTED=y
# default:
CONFIG_SOC_PHY_SUPPORTED=y
# default:
CONFIG_SOC_WIFI_SUPPORTED=y
# default:
CONFIG_SOC_SUPPORTS_SECURE_DL_MODE=y
# default:
CONFIG_SOC_ULP_SUPPORTED=y
# default:
CONFIG_SOC_LP_CORE_SUPPORTED=y
# default:
CONFIG_SOC_EFUSE_KEY_PURPOSE_FIELD=y
# default:
CONFIG_SOC_EFUSE_SUPPORTED=y
# default:
CONFIG_SOC_RTC_FAST_MEM_SUPPORTED=y
# default:
CONFIG_SOC_RTC_MEM_SUPPORTED=y
# default:
CONFIG_SOC_I2S_SUPPORTED=y
# default:
CONFIG_SOC_RMT_SUPPORTED=y
# default:
CONFIG_SOC_SDM_SUPPORTED=y
# default:
CONFIG_SOC_GPSPI_SUPPORTED=y
# default:
CONFIG_SOC_LEDC_SUPPORTED=y
# default:
CONFIG_SOC_I2C_SUPPORTED=y
# default:
CONFIG_SOC_SYSTIMER_SUPPORTED=y
# default:
CONFIG_SOC_SUPPORT_COEXISTENCE=y
# default:
CONFIG_SOC_AES_SUPPORTED=y
# default:
CONFIG_SOC_MPI_SUPPORTED=y
# default:
CONFIG_SOC_SHA_SUPPORTED=y
# default:
CONFIG_SOC_HMAC_SUPPORTED=y
# default:
CONFIG_SOC_DIG_SIGN_SUPPORTED=y
# default:
CONFIG_SOC_ECC_SUPPORTED=y
# default:
CONFIG_SOC_FLASH_ENC_SUPPORTED=y
# default:
CONFIG_SOC_SECURE_BOOT_SUPPORTED=y
# default:
CONFIG_SOC_SDIO_SLAVE_SUPPORTED=y
# default:
CONFIG_SOC_BOD_SUPPORTED=y
# default:
CONFIG_SOC_APM_SUPPORTED=y
# default:
CONFIG_SOC_PMU_SUPPORTED=y
# default:
CONFIG_SOC_PMU_PVT_SUPPORTED=y
# default:
CONFIG_SOC_PAU_SUPPORTED=y
# default:
CONFIG_SOC_RTC_TIMER_V2_SUPPORTED=y
# default:
CONFIG_SOC_LP_AON_SUPPORTED=y
# default:
CONFIG_SOC_LP_PERIPHERALS_SUPPORTED=y
# default:
CONFIG_SOC_LP_I2C_SUPPORTED=y
# default:
CONFIG_SOC_ULP_LP_UART_SUPPORTED=y
# default:
CONFIG_SOC_CLK_TREE_SUPPORTED=y
# default:
CONFIG_SOC_ASSIST_DEBUG_SUPPORTED=y
# default:
CONFIG_SOC_WDT_SUPPORTED=y
# default:
CONFIG_SOC_SPI_FLASH_SUPPORTED=y
# default:
CONFIG_SOC_RNG_SUPPORTED=y
# default:
CONFIG_SOC_LIGHT_SLEEP_SUPPORTED=y
# default:
CONFIG_SOC_DEEP_SLEEP_SUPPORTED=y
# default:
CONFIG_SOC_MODEM_CLOCK_SUPPORTED=y
# default:
CONFIG_SOC_PM_SUPPORTED=y
# default:
CONFIG_SOC_XTAL_SUPPORT_40M=y
# default:
CONFIG_SOC_XTAL_CLOCK_PATH_DEPENDS_ON_TOP_DOMAIN=y
# default:
CONFIG_SOC_AES_SUPPORT_DMA=y
# default:
CONFIG_SOC_AES_GDMA=y
# default:
CONFIG_SOC_AES_SUPPORT_AES_128=y
# default:
CONFIG_SOC_AES_SUPPORT_AES_256=y
# default:
CONFIG_SOC_ADC_DIG_CTRL_SUPPORTED=y
# default:
CONFIG_SOC_ADC_DIG_IIR_FILTER_SUPPORTED=y
# default:
CONFIG_SOC_ADC_MONITOR_SUPPORTED=y
# default:
CONFIG_SOC_ADC_DMA_SUPPORTED=y
# default:
CONFIG_SOC_ADC_PERIPH_NUM=1
# default:
CONFIG_SOC_ADC_MAX_CHANNEL_NUM=7
# default:
CONFIG_SOC_ADC_ATTEN_NUM=4
# default:
CONFIG_SOC_ADC_DIGI_CONTROLLER_NUM=1
# default:
CONFIG_SOC_ADC_PATT_LEN_MAX=8
# default:
CONFIG_SOC_ADC_DIGI_MAX_BITWIDTH=12
# default:
CONFIG_SOC_ADC_DIGI_MIN_BITWIDTH=12
# default:
CONFIG_SOC_ADC_DIGI_IIR_FILTER_NUM=2
# default:
CONFIG_SOC_ADC_DIGI_MONITOR_NUM=2
# default:
CONFIG_SOC_ADC_DIGI_RESULT_BYTES=4
# default:
CONFIG_SOC_ADC_DIGI_DATA_BYTES_PER_CONV=4
# default:
CONFIG_SOC_ADC_SAMPLE_FREQ_THRES_HIGH=83333
# default:
CONFIG_SOC_ADC_SAMPLE_FREQ_THRES_LOW=611
# default:
CONFIG_SOC_ADC_RTC_MIN_BITWIDTH=12
# default:
CONFIG_SOC_ADC_RTC_MAX_BITWIDTH=12
# default:
CONFIG_SOC_ADC_CALIBRATION_V1_SUPPORTED=y
# default:
CONFIG_SOC_ADC_SELF_HW_CALI_SUPPORTED=y
# default:
CONFIG_SOC_ADC_CALIB_CHAN_COMPENS_SUPPORTED=y
# default:
CONFIG_SOC_ADC_TEMPERATURE_SHARE_INTR=y
# default:
CONFIG_SOC_ADC_SHARED_POWER=y
# default:
CONFIG_SOC_BROWNOUT_RESET_SUPPORTED=y
# default:
CONFIG_SOC_SHARED_IDCACHE_SUPPORTED=y
# default:
CONFIG_SOC_CACHE_FREEZE_SUPPORTED=y
# default:
CONFIG_SOC_CPU_CORES_NUM=1
# default:
CONFIG_SOC_CPU_INTR_NUM=32
# default:
CONFIG_SOC_CPU_HAS_FLEXIBLE_INTC=y
# default:
CONFIG_SOC_INT_PLIC_SUPPORTED=y
# default:
CONFIG_SOC_CPU_HAS_CSR_PC=y
# default:
CONFIG_SOC_CPU_BREAKPOINTS_NUM=4
# default:
CONFIG_SOC_CPU_WATCHPOINTS_NUM=4
# default:
CONFIG_SOC_CPU_WATCHPOINT_MAX_REGION_SIZE=0x80000000
# default:
CONFIG_SOC_CPU_HAS_PMA=y
# default:
CONFIG_SOC_CPU_IDRAM_SPLIT_USING_PMP=y
# default:
CONFIG_SOC_CPU_PMP_REGION_GRANULARITY=4
# default:
CONFIG_SOC_CPU_MISALIGNED_ACCESS_ON_PMP_MISMATCH_ISSUE=y
# default:
CONFIG_SOC_DS_SIGNATURE_MAX_BIT_LEN=3072
# default:
CONFIG_SOC_DS_KEY_PARAM_MD_IV_LENGTH=16
# default:
CONFIG_SOC_DS_KEY_CHECK_MAX_WAIT_US=1100
# default:
CONFIG_SOC_AHB_GDMA_VERSION=1
# default:
CONFIG_SOC_GDMA_SUPPORT_ETM=y
# default:
CONFIG_SOC_GDMA_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_GPIO_PORT=1
# default:
CONFIG_SOC_GPIO_PIN_COUNT=31
# default:
CONFIG_SOC_GPIO_SUPPORT_PIN_GLITCH_FILTER=y
# default:
CONFIG_SOC_GPIO_FLEX_GLITCH_FILTER_NUM=8
# default:
CONFIG_SOC_GPIO_SUPPORT_ETM=y
# default:
CONFIG_SOC_GPIO_SUPPORT_HP_PERIPH_PD_SLEEP_WAKEUP=y
# default:
CONFIG_SOC_LP_IO_CLOCK_IS_INDEPENDENT=y
# default:
CONFIG_SOC_GPIO_IN_RANGE_MAX=30
# default:
CONFIG_SOC_GPIO_OUT_RANGE_MAX=30
# default:
CONFIG_SOC_GPIO_HP_PERIPH_PD_SLEEP_WAKEABLE_MASK=0
# default:
CONFIG_SOC_GPIO_HP_PERIPH_PD_SLEEP_WAKEABLE_PIN_CNT=8
# default:
CONFIG_SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK=0x000000007FFFFF00
# default:
CONFIG_SOC_GPIO_SUPPORT_FORCE_HOLD=y
# default:
CONFIG_SOC_GPIO_SUPPORT_HOLD_SINGLE_IO_IN_DSLP=y
# default:
CONFIG_SOC_GPIO_CLOCKOUT_BY_GPIO_MATRIX=y
# default:
CONFIG_SOC_CLOCKOUT_HAS_SOURCE_GATE=y
# default:
CONFIG_SOC_GPIO_CLOCKOUT_CHANNEL_NUM=3
# default:
CONFIG_SOC_RTCIO_PIN_COUNT=8
# default:
CONFIG_SOC_RTCIO_INPUT_OUTPUT_SUPPORTED=y
# default:
CONFIG_SOC_RTCIO_HOLD_SUPPORTED=y
# default:
CONFIG_SOC_RTCIO_WAKE_SUPPORTED=y
# default:
CONFIG_SOC_SDM_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_ETM_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_I2C_NUM=2
# default:
CONFIG_SOC_HP_I2C_NUM=1
# default:
CONFIG_SOC_LP_I2C_NUM=1
# default:
CONFIG_SOC_I2C_SUPPORT_XTAL=y
# default:
CONFIG_SOC_I2C_SUPPORT_RTC=y
# default:
CONFIG_SOC_I2C_SUPPORT_10BIT_ADDR=y
# default:
CONFIG_SOC_I2C_SUPPORT_SLAVE=y
# default:
CONFIG_SOC_I2C_SLAVE_SUPPORT_BROADCAST=y
# default:
CONFIG_SOC_I2C_SLAVE_CAN_GET_STRETCH_CAUSE=y
# default:
CONFIG_SOC_I2C_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_I2S_HW_VERSION_2=y
# default:
CONFIG_SOC_I2S_SUPPORTS_ETM=y
# default:
CONFIG_SOC_I2S_SUPPORTS_PCM=y
# default:
CONFIG_SOC_I2S_SUPPORTS_PDM=y
# default:
CONFIG_SOC_I2S_SUPPORTS_PDM_TX=y
# default:
CONFIG_SOC_I2S_SUPPORTS_PCM2PDM=y
# default:
CONFIG_SOC_I2S_SUPPORTS_PDM_RX=y
# default:
CONFIG_SOC_I2S_PDM_MAX_TX_LINES=2
# default:
CONFIG_SOC_I2S_PDM_MAX_RX_LINES=1
# default:
CONFIG_SOC_I2S_SUPPORTS_TDM=y
# default:
CONFIG_SOC_LEDC_SUPPORT_PLL_DIV_CLOCK=y
# default:
CONFIG_SOC_LEDC_SUPPORT_XTAL_CLOCK=y
# default:
CONFIG_SOC_LEDC_TIMER_NUM=4
# default:
CONFIG_SOC_LEDC_CHANNEL_NUM=6
# default:
CONFIG_SOC_LEDC_TIMER_BIT_WIDTH=20
# default:
CONFIG_SOC_LEDC_SUPPORT_FADE_STOP=y
# default:
CONFIG_SOC_LEDC_GAMMA_CURVE_FADE_SUPPORTED=y
# default:
CONFIG_SOC_LEDC_GAMMA_CURVE_FADE_RANGE_MAX=16
# default:
CONFIG_SOC_LEDC_FADE_PARAMS_BIT_WIDTH=10
# default:
CONFIG_SOC_LEDC_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_LEDC_SUPPORT_ETM=y
# default:
CONFIG_SOC_MMU_PAGE_SIZE_CONFIGURABLE=y
# default:
CONFIG_SOC_MMU_PAGE_SIZE_8KB_SUPPORTED=y
# default:
CONFIG_SOC_MMU_PERIPH_NUM=1
# default:
CONFIG_SOC_MMU_LINEAR_ADDRESS_REGION_NUM=1
# default:
CONFIG_SOC_MMU_DI_VADDR_SHARED=y
# default:
CONFIG_SOC_MPU_MIN_REGION_SIZE=0x20000000
# default:
CONFIG_SOC_MPU_REGIONS_MAX_NUM=8
# default:
CONFIG_SOC_PCNT_SUPPORT_RUNTIME_THRES_UPDATE=y
# default:
CONFIG_SOC_RMT_MEM_WORDS_PER_CHANNEL=48
# default:
CONFIG_SOC_RMT_SUPPORT_RX_PINGPONG=y
# default:
CONFIG_SOC_RMT_SUPPORT_TX_LOOP_COUNT=y
# default:
CONFIG_SOC_RMT_SUPPORT_TX_LOOP_AUTO_STOP=y
# default:
CONFIG_SOC_RMT_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_MCPWM_SWSYNC_CAN_PROPAGATE=y
# default:
CONFIG_SOC_MCPWM_SUPPORT_ETM=y
# default:
CONFIG_SOC_MCPWM_CAPTURE_CLK_FROM_GROUP=y
# default:
CONFIG_SOC_MCPWM_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_PARLIO_TX_UNIT_MAX_DATA_WIDTH=16
# default:
CONFIG_SOC_PARLIO_RX_UNIT_MAX_DATA_WIDTH=16
# default:
CONFIG_SOC_PARLIO_TX_RX_SHARE_INTERRUPT=y
# default:
CONFIG_SOC_PARLIO_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_MPI_MEM_BLOCKS_NUM=4
# default:
CONFIG_SOC_MPI_OPERATIONS_NUM=3
# default:
CONFIG_SOC_RSA_MAX_BIT_LEN=3072
# default:
CONFIG_SOC_SHA_DMA_MAX_BUFFER_SIZE=3968
# default:
CONFIG_SOC_SHA_SUPPORT_DMA=y
# default:
CONFIG_SOC_SHA_SUPPORT_RESUME=y
# default:
CONFIG_SOC_SHA_GDMA=y
# default:
CONFIG_SOC_SHA_SUPPORT_SHA1=y
# default:
CONFIG_SOC_SHA_SUPPORT_SHA224=y
# default:
CONFIG_SOC_SHA_SUPPORT_SHA256=y
# default:
CONFIG_SOC_SPI_PERIPH_NUM=2
# default:
CONFIG_SOC_SPI_MAX_CS_NUM=6
# default:
CONFIG_SOC_SPI_MAXIMUM_BUFFER_SIZE=64
# default:
CONFIG_SOC_SPI_SUPPORT_DDRCLK=y
# default:
CONFIG_SOC_SPI_SLAVE_SUPPORT_SEG_TRANS=y
# default:
CONFIG_SOC_SPI_SUPPORT_CD_SIG=y
# default:
CONFIG_SOC_SPI_SUPPORT_CONTINUOUS_TRANS=y
# default:
CONFIG_SOC_SPI_SUPPORT_SLAVE_HD_VER2=y
# default:
CONFIG_SOC_SPI_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_SPI_SUPPORT_CLK_XTAL=y
# default:
CONFIG_SOC_SPI_SUPPORT_CLK_PLL_F80M=y
# default:
CONFIG_SOC_SPI_SUPPORT_CLK_RC_FAST=y
# default:
CONFIG_SOC_SPI_SCT_SUPPORTED=y
# default:
CONFIG_SOC_SPI_SCT_REG_NUM=14
# default:
CONFIG_SOC_SPI_SCT_BUFFER_NUM_MAX=y
# default:
CONFIG_SOC_SPI_SCT_CONF_BITLEN_MAX=0x3FFFA
# default:
CONFIG_SOC_MEMSPI_IS_INDEPENDENT=y
# default:
CONFIG_SOC_SPI_MAX_PRE_DIVIDER=16
# default:
CONFIG_SOC_SPI_MEM_SUPPORT_AUTO_WAIT_IDLE=y
# default:
CONFIG_SOC_SPI_MEM_SUPPORT_AUTO_SUSPEND=y
# default:
CONFIG_SOC_SPI_MEM_SUPPORT_AUTO_RESUME=y
# default:
CONFIG_SOC_SPI_MEM_SUPPORT_IDLE_INTR=y
# default:
CONFIG_SOC_SPI_MEM_SUPPORT_SW_SUSPEND=y
# default:
CONFIG_SOC_SPI_MEM_SUPPORT_CHECK_SUS=y
# default:
CONFIG_SOC_SPI_MEM_SUPPORT_WRAP=y
# default:
CONFIG_SOC_SYSTIMER_COUNTER_NUM=2
# default:
CONFIG_SOC_SYSTIMER_ALARM_NUM=3
# default:
CONFIG_SOC_SYSTIMER_BIT_WIDTH_LO=32
# default:
CONFIG_SOC_SYSTIMER_BIT_WIDTH_HI=20
# default:
CONFIG_SOC_SYSTIMER_FIXED_DIVIDER=y
# default:
CONFIG_SOC_SYSTIMER_SUPPORT_RC_FAST=y
# default:
CONFIG_SOC_SYSTIMER_INT_LEVEL=y
# default:
CONFIG_SOC_SYSTIMER_ALARM_MISS_COMPENSATE=y
# default:
CONFIG_SOC_SYSTIMER_SUPPORT_ETM=y
# default:
CONFIG_SOC_LP_TIMER_BIT_WIDTH_LO=32
# default:
CONFIG_SOC_LP_TIMER_BIT_WIDTH_HI=16
# default:
CONFIG_SOC_TIMER_SUPPORT_ETM=y
# default:
CONFIG_SOC_TIMER_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_MWDT_SUPPORT_XTAL=y
# default:
CONFIG_SOC_MWDT_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_TWAI_CONTROLLER_NUM=2
# default:
CONFIG_SOC_TWAI_MASK_FILTER_NUM=1
# default:
CONFIG_SOC_TWAI_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_EFUSE_DIS_DOWNLOAD_ICACHE=y
# default:
CONFIG_SOC_EFUSE_DIS_PAD_JTAG=y
# default:
CONFIG_SOC_EFUSE_DIS_USB_JTAG=y
# default:
CONFIG_SOC_EFUSE_DIS_DIRECT_BOOT=y
# default:
CONFIG_SOC_EFUSE_SOFT_DIS_JTAG=y
# default:
CONFIG_SOC_EFUSE_DIS_ICACHE=y
# default:
CONFIG_SOC_EFUSE_BLOCK9_KEY_PURPOSE_QUIRK=y
# default:
CONFIG_SOC_EFUSE_XTS_AES_KEY_128=y
# default:
CONFIG_SOC_SECURE_BOOT_V2_RSA=y
# default:
CONFIG_SOC_SECURE_BOOT_V2_ECC=y
# default:
CONFIG_SOC_EFUSE_SECURE_BOOT_KEY_DIGESTS=3
# default:
CONFIG_SOC_EFUSE_REVOKE_BOOT_KEY_DIGESTS=y
# default:
CONFIG_SOC_SUPPORT_SECURE_BOOT_REVOKE_KEY=y
# default:
CONFIG_SOC_FLASH_ENCRYPTED_XTS_AES_BLOCK_MAX=64
# default:
CONFIG_SOC_FLASH_ENCRYPTION_XTS_AES=y
# default:
CONFIG_SOC_FLASH_ENCRYPTION_XTS_AES_128=y
# default:
CONFIG_SOC_APM_CTRL_FILTER_SUPPORTED=y
# default:
CONFIG_SOC_APM_LP_APM0_SUPPORTED=y
# default:
CONFIG_SOC_APM_SUPPORT_LP_TEE_CTRL=y
# default:
CONFIG_SOC_CRYPTO_DPA_PROTECTION_SUPPORTED=y
# default:
CONFIG_SOC_UART_NUM=3
# default:
CONFIG_SOC_UART_HP_NUM=2
# default:
CONFIG_SOC_UART_LP_NUM=1
# default:
CONFIG_SOC_UART_FIFO_LEN=128
# default:
CONFIG_SOC_LP_UART_FIFO_LEN=16
# default:
CONFIG_SOC_UART_BITRATE_MAX=5000000
# default:
CONFIG_SOC_UART_SUPPORT_RTC_CLK=y
# default:
CONFIG_SOC_UART_SUPPORT_XTAL_CLK=y
# default:
CONFIG_SOC_UART_SUPPORT_WAKEUP_INT=y
# default:
CONFIG_SOC_UART_HAS_LP_UART=y
# default:
CONFIG_SOC_UART_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_UART_WAKEUP_CHARS_SEQ_MAX_LEN=5
# default:
CONFIG_SOC_UART_WAKEUP_SUPPORT_ACTIVE_THRESH_MODE=y
# default:
CONFIG_SOC_UART_WAKEUP_SUPPORT_FIFO_THRESH_MODE=y
# default:
CONFIG_SOC_UART_WAKEUP_SUPPORT_START_BIT_MODE=y
# default:
CONFIG_SOC_UART_WAKEUP_SUPPORT_CHAR_SEQ_MODE=y
# default:
CONFIG_SOC_UHCI_NUM=1
# default:
CONFIG_SOC_COEX_HW_PTI=y
# default:
CONFIG_SOC_EXTERNAL_COEX_ADVANCE=y
# default:
CONFIG_SOC_PHY_DIG_REGS_MEM_SIZE=21
# default:
CONFIG_SOC_WIFI_LIGHT_SLEEP_CLK_WIDTH=12
# default:
CONFIG_SOC_RTC_MEM_SUPPORT_SPEED_MODE_SWITCH=y
# default:
CONFIG_SOC_PM_SUPPORT_WIFI_WAKEUP=y
# default:
CONFIG_SOC_PM_SUPPORT_BEACON_WAKEUP=y
# default:
CONFIG_SOC_PM_SUPPORT_BT_WAKEUP=y
# default:
CONFIG_SOC_PM_SUPPORT_EXT1_WAKEUP=y
# default:
CONFIG_SOC_PM_SUPPORT_EXT1_WAKEUP_MODE_PER_PIN=y
# default:
CONFIG_SOC_PM_SUPPORT_CPU_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_MODEM_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_XTAL32K_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_RC32K_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_RC_FAST_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_VDDSDIO_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_TOP_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_HP_AON_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_MAC_BB_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_RTC_PERIPH_PD=y
# default:
CONFIG_SOC_PM_SUPPORT_PMU_MODEM_STATE=y
# default:
CONFIG_SOC_PM_SUPPORT_PMU_CLK_ICG=y
# default:
CONFIG_SOC_PM_SUPPORT_DEEPSLEEP_CHECK_STUB_ONLY=y
# default:
CONFIG_SOC_PM_CPU_RETENTION_BY_SW=y
# default:
CONFIG_SOC_PM_MODEM_RETENTION_BY_REGDMA=y
# default:
CONFIG_SOC_PM_RETENTION_HAS_CLOCK_BUG=y
# default:
CONFIG_SOC_PM_MODEM_RF_FLAG_UPDATE_WORKAROUND=y
# default:
CONFIG_SOC_PM_PAU_LINK_NUM=4
# default:
CONFIG_SOC_PM_PAU_REGDMA_LINK_MULTI_ADDR=y
# default:
CONFIG_SOC_PM_PAU_REGDMA_LINK_WIFIMAC=y
# default:
CONFIG_SOC_PM_PAU_REGDMA_UPDATE_CACHE_BEFORE_WAIT_COMPARE=y
# default:
CONFIG_SOC_PM_PMU_MIN_SLP_SLOW_CLK_CYCLE_FIXED=y
# default:
CONFIG_SOC_PM_RETENTION_MODULE_NUM=32
# default:
CONFIG_SOC_CLK_RC_FAST_SUPPORT_CALIBRATION=y
# default:
CONFIG_SOC_MODEM_CLOCK_IS_INDEPENDENT=y
# default:
CONFIG_SOC_CLK_XTAL32K_SUPPORTED=y
# default:
CONFIG_SOC_CLK_OSC_SLOW_SUPPORTED=y
# default:
CONFIG_SOC_CLK_RC32K_SUPPORTED=y
# default:
CONFIG_SOC_CLK_LP_FAST_SUPPORT_XTAL_D2=y
# default:
CONFIG_SOC_RCC_IS_INDEPENDENT=y
# default:
CONFIG_SOC_TEMPERATURE_SENSOR_SUPPORT_FAST_RC=y
# default:
CONFIG_SOC_TEMPERATURE_SENSOR_SUPPORT_XTAL=y
# default:
CONFIG_SOC_TEMPERATURE_SENSOR_INTR_SUPPORT=y
# default:
CONFIG_SOC_TEMPERATURE_SENSOR_SUPPORT_ETM=y
# default:
CONFIG_SOC_TEMPERATURE_SENSOR_SUPPORT_SLEEP_RETENTION=y
# default:
CONFIG_SOC_TEMPERATURE_SENSOR_UNDER_PD_TOP_DOMAIN=y
# default:
CONFIG_SOC_RNG_CLOCK_IS_INDEPENDENT=y
# default:
CONFIG_SOC_WIFI_HW_TSF=y
# default:
CONFIG_SOC_WIFI_FTM_SUPPORT=y
# default:
CONFIG_SOC_WIFI_GCMP_SUPPORT=y
# default:
CONFIG_SOC_WIFI_WAPI_SUPPORT=y
# default:
CONFIG_SOC_WIFI_TXOP_SUPPORT=y
# default:
CONFIG_SOC_WIFI_CSI_SUPPORT=y
# default:
CONFIG_SOC_WIFI_MESH_SUPPORT=y
# default:
CONFIG_SOC_WIFI_HE_SUPPORT=y
# default:
CONFIG_SOC_WIFI_MAC_VERSION_NUM=2
# default:
CONFIG_SOC_BLE_SUPPORTED=y
# default:
CONFIG_SOC_BLE_MESH_SUPPORTED=y
# default:
CONFIG_SOC_ESP_NIMBLE_CONTROLLER=y
# default:
CONFIG_SOC_BLE_50_SUPPORTED=y
# default:
CONFIG_SOC_BLE_DEVICE_PRIVACY_SUPPORTED=y
# default:
CONFIG_SOC_BLE_POWER_CONTROL_SUPPORTED=y
# default:
CONFIG_SOC_BLE_PERIODIC_ADV_ENH_SUPPORTED=y
# default:
CONFIG_SOC_BLUFI_SUPPORTED=y
# default:
CONFIG_SOC_BLE_MULTI_CONN_OPTIMIZATION=y
# default:
CONFIG_SOC_BLE_SUBRATE_SUPPORTED=y
# default:
CONFIG_SOC_BLE_PERIODIC_ADV_WITH_RESPONSE=y
# default:
CONFIG_SOC_BLE_USE_WIFI_PWR_CLK_WORKAROUND=y
# default:
CONFIG_SOC_PHY_COMBO_MODULE=y
# default:
CONFIG_SOC_CAPS_NO_RESET_BY_ANA_BOD=y
# default:
CONFIG_SOC_LP_CORE_SINGLE_INTERRUPT_VECTOR=y
# default:
CONFIG_SOC_LP_CORE_SUPPORT_ETM=y
# default:
CONFIG_SOC_DEBUG_HAVE_OCD_STUB_BINS=y
# default:
CONFIG_IDF_CMAKE=y
# default:
CONFIG_IDF_TOOLCHAIN="gcc"
# default:
CONFIG_IDF_TOOLCHAIN_GCC=y
# default:
CONFIG_IDF_TARGET_ARCH_RISCV=y
# default:
CONFIG_IDF_TARGET_ARCH="riscv"
# default:
CONFIG_IDF_TARGET="esp32c6"
# default:
CONFIG_IDF_INIT_VERSION="6.0.0"
# default:
CONFIG_IDF_TARGET_ESP32C6=y
# default:
CONFIG_IDF_FIRMWARE_CHIP_ID=0x000D

#
# Build type
#
# default:
CONFIG_APP_BUILD_TYPE_APP_2NDBOOT=y
# default:
# CONFIG_APP_BUILD_TYPE_RAM is not set
# default:
CONFIG_APP_BUILD_GENERATE_BINARIES=y
# default:
CONFIG_APP_BUILD_BOOTLOADER=y
# default:
CONFIG_APP_BUILD_USE_FLASH_SECTIONS=y
CONFIG_APP_REPRODUCIBLE_BUILD=y
# default:
# CONFIG_APP_NO_BLOBS is not set
# end of Build type

#
# App Update config
#
# end of App Update config

#
# Bootloader config
#

#
# Bootloader manager
#
# default:
CONFIG_BOOTLOADER_PROJECT_VER=1
# end of Bootloader manager

#
# Application Rollback
#
# default:
# CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE is not set
# end of Application Rollback

#
# Recovery Bootloader and Rollback
#
# end of Recovery Bootloader and Rollback

# default:
CONFIG_BOOTLOADER_OFFSET_IN_FLASH=0x0
# default:
CONFIG_BOOTLOADER_COMPILER_OPTIMIZATION_SIZE=y
# default:
# CONFIG_BOOTLOADER_COMPILER_OPTIMIZATION_DEBUG is not set
# default:
# CONFIG_BOOTLOADER_COMPILER_OPTIMIZATION_PERF is not set

#
# Log
#
# default:
CONFIG_BOOTLOADER_LOG_VERSION_1=y
# default:
CONFIG_BOOTLOADER_LOG_VERSION=1
# CONFIG_BOOTLOADER_LOG_LEVEL_NONE is not set
CONFIG_BOOTLOADER_LOG_LEVEL_ERROR=y
# CONFIG_BOOTLOADER_LOG_LEVEL_WARN is not set
# CONFIG_BOOTLOADER_LOG_LEVEL_INFO is not set
# CONFIG_BOOTLOADER_LOG_LEVEL_DEBUG is not set
# CONFIG_BOOTLOADER_LOG_LEVEL_VERBOSE is not set
# default:
CONFIG_BOOTLOADER_LOG_LEVEL=1

#
# Format
#
# default:
# CONFIG_BOOTLOADER_LOG_COLORS is not set
# default:
CONFIG_BOOTLOADER_LOG_TIMESTAMP_SOURCE_CPU_TICKS=y
# end of Format

#
# Settings
#
# default:
CONFIG_BOOTLOADER_LOG_MODE_TEXT_EN=y
# default:
CONFIG_BOOTLOADER_LOG_MODE_TEXT=y
# end of Settings
# end of Log

# default:
CONFIG_BOOTLOADER_CPU_CLK_FREQ_MHZ=80

#
# Serial Flash Configurations
#
# default:
# CONFIG_BOOTLOADER_FLASH_DC_AWARE is not set
# default:
CONFIG_BOOTLOADER_FLASH_XMC_SUPPORT=y
# end of Serial Flash Configurations

# default:
# CONFIG_BOOTLOADER_FACTORY_RESET is not set
# default:
# CONFIG_BOOTLOADER_APP_TEST is not set
# default:
CONFIG_BOOTLOADER_REGION_PROTECTION_ENABLE=y
# default:
CONFIG_BOOTLOADER_WDT_ENABLE=y
# default:
# CONFIG_BOOTLOADER_WDT_DISABLE_IN_USER_CODE is not set
# default:
CONFIG_BOOTLOADER_WDT_TIME_MS=9000
# default:
# CONFIG_BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP is not set
# default:
# CONFIG_BOOTLOADER_SKIP_VALIDATE_ON_POWER_ON is not set
# default:
# CONFIG_BOOTLOADER_SKIP_VALIDATE_ALWAYS is not set
# default:
CONFIG_BOOTLOADER_RESERVE_RTC_SIZE=0
# default:
# CONFIG_BOOTLOADER_CUSTOM_RESERVE_RTC is not set
# end of Bootloader config

#
# Security features
#
# default:
CONFIG_SECURE_BOOT_V2_RSA_SUPPORTED=y
# default:
CONFIG_SECURE_BOOT_V2_ECC_SUPPORTED=y
# default:
CONFIG_SECURE_BOOT_V2_PREFERRED=y
# default:
# CONFIG_SECURE_SIGNED_APPS_NO_SECURE_BOOT is not set
# default:
# CONFIG_SECURE_BOOT is not set
# default:
# CONFIG_SECURE_FLASH_ENC_ENABLED is not set
# default:
CONFIG_SECURE_ROM_DL_MODE_ENABLED=y
# end of Security features

#
# Application manager
#
# default:
# CONFIG_APP_EXCLUDE_PROJECT_VER_VAR is not set
# default:
# CONFIG_APP_EXCLUDE_PROJECT_NAME_VAR is not set
# default:
# CONFIG_APP_PROJECT_VER_FROM_CONFIG is not set
# default:
CONFIG_APP_RETRIEVE_LEN_ELF_SHA=9
# end of Application manager

# default:
CONFIG_ESP_ROM_HAS_CRC_LE=y
# default:
CONFIG_ESP_ROM_HAS_CRC_BE=y
# default:
CONFIG_ESP_ROM_HAS_JPEG_DECODE=y
# default:
CONFIG_ESP_ROM_UART_CLK_IS_XTAL=y
# default:
CONFIG_ESP_ROM_USB_SERIAL_DEVICE_NUM=3
# default:
CONFIG_ESP_ROM_HAS_RETARGETABLE_LOCKING=y
# default:
CONFIG_ESP_ROM_GET_CLK_FREQ=y
# default:
CONFIG_ESP_ROM_HAS_RVFPLIB=y
# default:
CONFIG_ESP_ROM_HAS_HAL_WDT=y
# default:
CONFIG_ESP_ROM_HAS_HAL_SYSTIMER=y
# default:
CONFIG_ESP_ROM_SYSTIMER_INIT_PATCH=y
# default:
CONFIG_ESP_ROM_HAS_HEAP_TLSF=y
# default:
CONFIG_ESP_ROM_TLSF_CHECK_PATCH=y
# default:
CONFIG_ESP_ROM_MULTI_HEAP_WALK_PATCH=y
# default:
CONFIG_ESP_ROM_HAS_LAYOUT_TABLE=y
# default:
CONFIG_ESP_ROM_HAS_SPI_FLASH=y
# default:
CONFIG_ESP_ROM_HAS_SPI_FLASH_MMAP=y
# default:
CONFIG_ESP_ROM_HAS_REGI2C_BUG=y
# default:
CONFIG_ESP_ROM_HAS_NEWLIB=y
# default:
CONFIG_ESP_ROM_HAS_NEWLIB_NORMAL_FORMAT=y
# default:
CONFIG_ESP_ROM_REV0_HAS_NO_ECDSA_INTERFACE=y
# default:
CONFIG_ESP_ROM_WDT_INIT_PATCH=y
# default:
CONFIG_ESP_ROM_NEEDS_SET_CACHE_MMU_SIZE=y
# default:
CONFIG_ESP_ROM_RAM_APP_NEEDS_MMU_INIT=y
# default:
CONFIG_ESP_ROM_HAS_SW_FLOAT=y
# default:
CONFIG_ESP_ROM_USB_OTG_NUM=-1
# default:
CONFIG_ESP_ROM_HAS_VERSION=y
# default:
CONFIG_ESP_ROM_SUPPORT_DEEP_SLEEP_WAKEUP_STUB=y
# default:
CONFIG_ESP_ROM_HAS_OUTPUT_PUTC_FUNC=y
# default:
CONFIG_ESP_ROM_NO_USB_SERIAL_OUTPUT_API=y
# default:
CONFIG_ESP_ROM_HAS_SUBOPTIMAL_NEWLIB_ON_MISALIGNED_MEMORY=y
# default:
CONFIG_ESP_ROM_SUPPORT_SECURE_BOOT_FAST_WAKEUP=y

#
# Boot ROM Behavior
#
# default:
CONFIG_BOOT_ROM_LOG_ALWAYS_ON=y
# default:
# CONFIG_BOOT_ROM_LOG_ALWAYS_OFF is not set
# default:
# CONFIG_BOOT_ROM_LOG_ON_GPIO_HIGH is not set
# default:
# CONFIG_BOOT_ROM_LOG_ON_GPIO_LOW is not set
# end of Boot ROM Behavior

#
# Serial flasher config
#
# default:
# CONFIG_ESPTOOLPY_NO_STUB is not set
# default:
# CONFIG_ESPTOOLPY_FLASHMODE_QIO is not set
# default:
# CONFIG_ESPTOOLPY_FLASHMODE_QOUT is not set
# default:
CONFIG_ESPTOOLPY_FLASHMODE_DIO=y
# default:
# CONFIG_ESPTOOLPY_FLASHMODE_DOUT is not set
# default:
CONFIG_ESPTOOLPY_FLASH_SAMPLE_MODE_STR=y
# default:
CONFIG_ESPTOOLPY_FLASHMODE="dio"
# default:
CONFIG_ESPTOOLPY_FLASHFREQ_80M=y
# default:
# CONFIG_ESPTOOLPY_FLASHFREQ_40M is not set
# default:
# CONFIG_ESPTOOLPY_FLASHFREQ_20M is not set
# default:
CONFIG_ESPTOOLPY_FLASHFREQ="80m"
# CONFIG_ESPTOOLPY_FLASHSIZE_1MB is not set
# CONFIG_ESPTOOLPY_FLASHSIZE_2MB is not set
CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y
# CONFIG_ESPTOOLPY_FLASHSIZE_8MB is not set
# CONFIG_ESPTOOLPY_FLASHSIZE_16MB is not set
# CONFIG_ESPTOOLPY_FLASHSIZE_32MB is not set
# CONFIG_ESPTOOLPY_FLASHSIZE_64MB is not set
# CONFIG_ESPTOOLPY_FLASHSIZE_128MB is not set
# default:
CONFIG_ESPTOOLPY_FLASHSIZE="4MB"
CONFIG_ESPTOOLPY_HEADER_FLASHSIZE_UPDATE=y
# default:
CONFIG_ESPTOOLPY_BEFORE_RESET=y
# default:
# CONFIG_ESPTOOLPY_BEFORE_NORESET is not set
# default:
CONFIG_ESPTOOLPY_BEFORE="default-reset"
# default:
CONFIG_ESPTOOLPY_AFTER_RESET=y
# default:
# CONFIG_ESPTOOLPY_AFTER_NORESET is not set
# default:
CONFIG_ESPTOOLPY_AFTER="hard-reset"
# default:
CONFIG_ESPTOOLPY_MONITOR_BAUD=115200
# end of Serial flasher config

#
# Partition Table
#
# default:
CONFIG_PARTITION_TABLE_SINGLE_APP=y
# default:
# CONFIG_PARTITION_TABLE_SINGLE_APP_LARGE is not set
# default:
# CONFIG_PARTITION_TABLE_TWO_OTA is not set
# default:
# CONFIG_PARTITION_TABLE_TWO_OTA_LARGE is not set
# default:
# CONFIG_PARTITION_TABLE_CUSTOM is not set
# default:
CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="partitions.csv"
# default:
CONFIG_PARTITION_TABLE_FILENAME="partitions_singleapp.csv"
# default:
CONFIG_PARTITION_TABLE_OFFSET=0x8000
# default:
CONFIG_PARTITION_TABLE_MD5=y
# end of Partition Table

#
# Compiler options
#
# CONFIG_COMPILER_OPTIMIZATION_DEBUG is not set
CONFIG_COMPILER_OPTIMIZATION_SIZE=y
# CONFIG_COMPILER_OPTIMIZATION_PERF is not set
# CONFIG_COMPILER_OPTIMIZATION_NONE is not set
# CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_ENABLE is not set
# CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_SILENT is not set
CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_DISABLE=y
# default:
# CONFIG_COMPILER_ASSERT_NDEBUG_EVALUATE is not set
# default:
# CONFIG_COMPILER_FLOAT_LIB_FROM_GCCLIB is not set
# default:
CONFIG_COMPILER_FLOAT_LIB_FROM_RVFPLIB=y
# default:
CONFIG_COMPILER_OPTIMIZATION_ASSERTION_LEVEL=0
# default:
# CONFIG_COMPILER_OPTIMIZATION_CHECKS_SILENT is not set
# default:
CONFIG_COMPILER_HIDE_PATHS_MACROS=y
# default:
# CONFIG_COMPILER_CXX_EXCEPTIONS is not set
# default:
# CONFIG_COMPILER_CXX_RTTI is not set
# default:
CONFIG_COMPILER_STACK_CHECK_MODE_NONE=y
# default:
# CONFIG_COMPILER_STACK_CHECK_MODE_NORM is not set
# default:
# CONFIG_COMPILER_STACK_CHECK_MODE_STRONG is not set
# default:
# CONFIG_COMPILER_STACK_CHECK_MODE_ALL is not set
# default:
# CONFIG_COMPILER_NO_MERGE_CONSTANTS is not set
# default:
# CONFIG_COMPILER_WARN_WRITE_STRINGS is not set
# default:
# CONFIG_COMPILER_SAVE_RESTORE_LIBCALLS is not set
# default:
# CONFIG_COMPILER_DISABLE_DEFAULT_ERRORS is not set
# default:
# CONFIG_COMPILER_DISABLE_GCC12_WARNINGS is not set
# default:
# CONFIG_COMPILER_DISABLE_GCC13_WARNINGS is not set
# default:
# CONFIG_COMPILER_DISABLE_GCC14_WARNINGS is not set
# default:
# CONFIG_COMPILER_DISABLE_GCC15_WARNINGS is not set
# default:
# CONFIG_COMPILER_DUMP_RTL_FILES is not set
# default:
CONFIG_COMPILER_RT_LIB_GCCLIB=y
# default:
CONFIG_COMPILER_RT_LIB_NAME="gcc"
# default:
CONFIG_COMPILER_ORPHAN_SECTIONS_ERROR=y
# default:
# CONFIG_COMPILER_ORPHAN_SECTIONS_WARNING is not set
# default:
# CONFIG_COMPILER_ORPHAN_SECTIONS_PLACE is not set
# default:
# CONFIG_COMPILER_STATIC_ANALYZER is not set
# default:
CONFIG_COMPILER_CXX_GLIBCXX_CONSTEXPR_NO_CHANGE=y
# default:
# CONFIG_COMPILER_CXX_GLIBCXX_CONSTEXPR_COLD_CONSTEXPR is not set
# default:
# CONFIG_COMPILER_CXX_GLIBCXX_CONSTEXPR_COLD is not set
# end of Compiler options

#
# Component config
#

#
# !!! MINIMAL_BUILD is enabled !!!
#

#
# Only common components and those transitively required by the main component are listed
#

#
# If a component configuration is missing, please add it to the main component's requirements
#

#
# Console Library
#
# default:
# CONFIG_CONSOLE_SORTED_HELP is not set
# end of Console Library

#
# eFuse Bit Manager
#
# default:
# CONFIG_EFUSE_CUSTOM_TABLE is not set
# default:
# CONFIG_EFUSE_VIRTUAL is not set
# default:
CONFIG_EFUSE_MAX_BLK_LEN=256
# end of eFuse Bit Manager

#
# Common ESP-related
#
# default:
CONFIG_ESP_ERR_TO_NAME_LOOKUP=y
# end of Common ESP-related

#
# GDMA Configurations
#
# default:
CONFIG_GDMA_CTRL_FUNC_IN_IRAM=y
# default:
CONFIG_GDMA_ISR_HANDLER_IN_IRAM=y
# default:
CONFIG_GDMA_OBJ_DRAM_SAFE=y
# default:
# CONFIG_GDMA_ENABLE_DEBUG_LOG is not set
# end of GDMA Configurations

#
# ESP-Driver:GPIO Configurations
#
# default:
# CONFIG_GPIO_CTRL_FUNC_IN_IRAM is not set
# end of ESP-Driver:GPIO Configurations

#
# ESP-Driver:UART Configurations
#
# default:
# CONFIG_UART_ISR_IN_IRAM is not set
# end of ESP-Driver:UART Configurations

#
# ESP-Driver:UHCI Configurations
#
# default:
# CONFIG_UHCI_ISR_HANDLER_IN_IRAM is not set
# default:
# CONFIG_UHCI_ISR_CACHE_SAFE is not set
# default:
# CONFIG_UHCI_ENABLE_DEBUG_LOG is not set
# end of ESP-Driver:UHCI Configurations

#
# ESP-Driver:USB Serial/JTAG Configuration
#
# default:
CONFIG_USJ_ENABLE_USB_SERIAL_JTAG=y
# end of ESP-Driver:USB Serial/JTAG Configuration

#
# Hardware Settings
#
# default:
CONFIG_ESP_HW_SUPPORT_FUNC_IN_IRAM=y

#
# Chip revision
#
# default:
CONFIG_ESP32C6_REV_MIN_0=y
# default:
# CONFIG_ESP32C6_REV_MIN_1 is not set
# default:
# CONFIG_ESP32C6_REV_MIN_2 is not set
# default:
CONFIG_ESP32C6_REV_MIN_FULL=0
# default:
CONFIG_ESP_REV_MIN_FULL=0

#
# Maximum Supported ESP32-C6 Revision (Rev v0.99)
#
# default:
CONFIG_ESP32C6_REV_MAX_FULL=99
# default:
CONFIG_ESP_REV_MAX_FULL=99
# default:
CONFIG_ESP_EFUSE_BLOCK_REV_MIN_FULL=0
# default:
CONFIG_ESP_EFUSE_BLOCK_REV_MAX_FULL=99

#
# Maximum Supported ESP32-C6 eFuse Block Revision (eFuse Block Rev v0.99)
#
# end of Chip revision

#
# MAC Config
#
# default:
CONFIG_ESP_MAC_ADDR_UNIVERSE_WIFI_STA=y
# default:
CONFIG_ESP_MAC_ADDR_UNIVERSE_WIFI_AP=y
# default:
CONFIG_ESP_MAC_ADDR_UNIVERSE_BT=y
# default:
CONFIG_ESP_MAC_ADDR_UNIVERSE_ETH=y
# default:
CONFIG_ESP_MAC_ADDR_UNIVERSE_IEEE802154=y
# default:
CONFIG_ESP_MAC_UNIVERSAL_MAC_ADDRESSES_FOUR=y
# default:
CONFIG_ESP_MAC_UNIVERSAL_MAC_ADDRESSES=4
# default:
# CONFIG_ESP32C6_UNIVERSAL_MAC_ADDRESSES_TWO is not set
# default:
CONFIG_ESP32C6_UNIVERSAL_MAC_ADDRESSES_FOUR=y
# default:
CONFIG_ESP32C6_UNIVERSAL_MAC_ADDRESSES=4
# default:
# CONFIG_ESP_MAC_USE_CUSTOM_MAC_AS_BASE_MAC is not set
# end of MAC Config

#
# Sleep Config
#
# default:
# CONFIG_ESP_SLEEP_POWER_DOWN_FLASH is not set
# default:
CONFIG_ESP_SLEEP_FLASH_LEAKAGE_WORKAROUND=y
# default:
# CONFIG_ESP_SLEEP_MSPI_NEED_ALL_IO_PU is not set
# default:
CONFIG_ESP_SLEEP_GPIO_RESET_WORKAROUND=y
# default:
CONFIG_ESP_SLEEP_WAIT_FLASH_READY_EXTRA_DELAY=0
# default:
# CONFIG_ESP_SLEEP_CACHE_SAFE_ASSERTION is not set
# default:
# CONFIG_ESP_SLEEP_DEBUG is not set
# default:
CONFIG_ESP_SLEEP_GPIO_ENABLE_INTERNAL_RESISTORS=y
# end of Sleep Config

#
# RTC Clock Config
#
# default:
CONFIG_RTC_CLK_SRC_INT_RC=y
# default:
# CONFIG_RTC_CLK_SRC_EXT_CRYS is not set
# default:
# CONFIG_RTC_CLK_SRC_EXT_OSC is not set
# default:
CONFIG_RTC_CLK_CAL_CYCLES=1024
# default:
CONFIG_RTC_CLK_FUNC_IN_IRAM=y
# default:
CONFIG_RTC_TIME_FUNC_IN_IRAM=y
# end of RTC Clock Config

#
# Peripheral Control
#
# default:
CONFIG_ESP_PERIPH_CTRL_FUNC_IN_IRAM=y
# default:
CONFIG_ESP_REGI2C_CTRL_FUNC_IN_IRAM=y
# default:
# CONFIG_ESP_MODEM_CLOCK_ENABLE_CHECKING is not set
# end of Peripheral Control

#
# Event Task Matrix (ETM) Configurations
#
# default:
# CONFIG_ETM_ENABLE_DEBUG_LOG is not set
# end of Event Task Matrix (ETM) Configurations

#
# Main XTAL Config
#
# default:
CONFIG_XTAL_FREQ_40=y
# default:
CONFIG_XTAL_FREQ=40
# end of Main XTAL Config

#
# Power Supplier
#

#
# Brownout Detector
#
# default:
CONFIG_ESP_BROWNOUT_DET=y
# default:
CONFIG_ESP_BROWNOUT_DET_LVL_SEL_7=y
# default:
# CONFIG_ESP_BROWNOUT_DET_LVL_SEL_6 is not set
# default:
# CONFIG_ESP_BROWNOUT_DET_LVL_SEL_5 is not set
# default:
# CONFIG_ESP_BROWNOUT_DET_LVL_SEL_4 is not set
# default:
# CONFIG_ESP_BROWNOUT_DET_LVL_SEL_3 is not set
# default:
# CONFIG_ESP_BROWNOUT_DET_LVL_SEL_2 is not set
# default:
CONFIG_ESP_BROWNOUT_DET_LVL=7
# default:
CONFIG_ESP_BROWNOUT_USE_INTR=y
# end of Brownout Detector
# end of Power Supplier

# default:
# CONFIG_ESP_ENABLE_PVT is not set
# default:
CONFIG_ESP_INTR_IN_IRAM=y
# end of Hardware Settings

#
# LibC
#
# default:
# CONFIG_LIBC_NEWLIB is not set
# default:
CONFIG_LIBC_PICOLIBC=y
# default:
CONFIG_LIBC_PICOLIBC_NEWLIB_COMPATIBILITY=y
# default:
CONFIG_LIBC_MISC_IN_IRAM=y
# default:
CONFIG_LIBC_LOCKS_PLACE_IN_IRAM=y
# default:
CONFIG_LIBC_STDOUT_LINE_ENDING_CRLF=y
# default:
# CONFIG_LIBC_STDOUT_LINE_ENDING_LF is not set
# default:
# CONFIG_LIBC_STDOUT_LINE_ENDING_CR is not set
# default:
# CONFIG_LIBC_STDIN_LINE_ENDING_CRLF is not set
# default:
# CONFIG_LIBC_STDIN_LINE_ENDING_LF is not set
# default:
CONFIG_LIBC_STDIN_LINE_ENDING_CR=y
# default:
CONFIG_LIBC_TIME_SYSCALL_USE_RTC_HRT=y
# default:
# CONFIG_LIBC_TIME_SYSCALL_USE_RTC is not set
# default:
# CONFIG_LIBC_TIME_SYSCALL_USE_HRT is not set
# default:
# CONFIG_LIBC_TIME_SYSCALL_USE_NONE is not set
# default:
CONFIG_LIBC_OPTIMIZED_MISALIGNED_ACCESS=y
# default:
CONFIG_LIBC_ASSERT_BUFFER_SIZE=200
# end of LibC

#
# ESP-MM: Memory Management Configurations
#
# end of ESP-MM: Memory Management Configurations

#
# Partition API Configuration
#
# end of Partition API Configuration

#
# Power Management
#
# default:
CONFIG_PM_SLEEP_FUNC_IN_IRAM=y
# default:
# CONFIG_PM_ENABLE is not set
# default:
CONFIG_PM_SLP_IRAM_OPT=y
# default:
CONFIG_PM_POWER_DOWN_CPU_IN_LIGHT_SLEEP=y
# default:
CONFIG_PM_CPU_RETENTION_DYNAMIC=y
# default:
# CONFIG_PM_CPU_RETENTION_STATIC is not set
# default:
# CONFIG_PM_POWER_DOWN_PERIPHERAL_IN_LIGHT_SLEEP is not set
# default:
CONFIG_PM_ESP_SLEEP_POWER_DOWN_CPU=y
# end of Power Management

#
# ESP PSRAM
#

#
# ESP Ringbuf
#
# default:
# CONFIG_RINGBUF_IN_IRAM is not set
# default:
# CONFIG_RINGBUF_PLACE_ISR_FUNCTIONS_INTO_FLASH is not set
# end of ESP Ringbuf

#
# ESP-ROM
#
# default:
CONFIG_ESP_ROM_PRINT_IN_IRAM=y
# end of ESP-ROM

#
# ESP Security Specific
#

#
# Crypto DPA Protection
#
# default:
CONFIG_ESP_CRYPTO_DPA_PROTECTION_AT_STARTUP=y
# default:
CONFIG_ESP_CRYPTO_DPA_PROTECTION_LEVEL_LOW=y
# default:
# CONFIG_ESP_CRYPTO_DPA_PROTECTION_LEVEL_MEDIUM is not set
# default:
# CONFIG_ESP_CRYPTO_DPA_PROTECTION_LEVEL_HIGH is not set
# default:
CONFIG_ESP_CRYPTO_DPA_PROTECTION_LEVEL=1
# end of Crypto DPA Protection
# end of ESP Security Specific

#
# ESP-STDIO
#
# CONFIG_ESP_CONSOLE_UART_DEFAULT is not set
CONFIG_ESP_CONSOLE_USB_SERIAL_JTAG=y
# CONFIG_ESP_CONSOLE_UART_CUSTOM is not set
# CONFIG_ESP_CONSOLE_NONE is not set
# default:
CONFIG_ESP_CONSOLE_SECONDARY_NONE=y
# default:
CONFIG_ESP_CONSOLE_USB_SERIAL_JTAG_ENABLED=y
# default:
CONFIG_ESP_CONSOLE_UART_NUM=-1
# default:
CONFIG_ESP_CONSOLE_ROM_SERIAL_PORT_NUM=3
# end of ESP-STDIO

#
# ESP System Settings
#
CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ_80=y
# CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ_120 is not set
# CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ_160 is not set
# default:
CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ=80
# default:
CONFIG_ESP_SYSTEM_IN_IRAM=y
# default:
# CONFIG_ESP_SYSTEM_PANIC_PRINT_HALT is not set
# default:
CONFIG_ESP_SYSTEM_PANIC_PRINT_REBOOT=y
# default:
# CONFIG_ESP_SYSTEM_PANIC_SILENT_REBOOT is not set
# default:
CONFIG_ESP_SYSTEM_PANIC_REBOOT_DELAY_SECONDS=0
# default:
CONFIG_ESP_SYSTEM_SINGLE_CORE_MODE=y
# default:
CONFIG_ESP_SYSTEM_RTC_FAST_MEM_AS_HEAP_DEPCHECK=y
# default:
CONFIG_ESP_SYSTEM_ALLOW_RTC_FAST_MEM_AS_HEAP=y
# default:
CONFIG_ESP_SYSTEM_NO_BACKTRACE=y
# default:
# CONFIG_ESP_SYSTEM_USE_EH_FRAME is not set
# default:
# CONFIG_ESP_SYSTEM_USE_FRAME_POINTER is not set
# default:
CONFIG_ESP_SYSTEM_MEMPROT=y
# default:
CONFIG_ESP_SYSTEM_MEMPROT_PMP=y
# default:
# CONFIG_ESP_SYSTEM_MEMPROT_PMP_LP_CORE_RESERVE_MEM_EXEC is not set
# default:
CONFIG_ESP_SYSTEM_EVENT_QUEUE_SIZE=32
# default:
CONFIG_ESP_SYSTEM_EVENT_TASK_STACK_SIZE=2304
# default:
CONFIG_ESP_MAIN_TASK_STACK_SIZE=3584
# default:
CONFIG_ESP_MAIN_TASK_AFFINITY_CPU0=y
# default:
# CONFIG_ESP_MAIN_TASK_AFFINITY_NO_AFFINITY is not set
# default:
CONFIG_ESP_MAIN_TASK_AFFINITY=0x0
# default:
CONFIG_ESP_MINIMAL_SHARED_STACK_SIZE=2048
# default:
CONFIG_ESP_INT_WDT=y
# default:
CONFIG_ESP_INT_WDT_TIMEOUT_MS=300
# default:
CONFIG_ESP_TASK_WDT_EN=y
# default:
CONFIG_ESP_TASK_WDT_INIT=y
# default:
# CONFIG_ESP_TASK_WDT_PANIC is not set
# default:
CONFIG_ESP_TASK_WDT_TIMEOUT_S=5
# default:
CONFIG_ESP_TASK_WDT_CHECK_IDLE_TASK_CPU0=y
# default:
# CONFIG_ESP_PANIC_HANDLER_IRAM is not set
# default:
# CONFIG_ESP_DEBUG_STUBS_ENABLE is not set
# default:
# CONFIG_ESP_DEBUG_INCLUDE_OCD_STUB_BINS is not set
# default:
CONFIG_ESP_DEBUG_OCDAWARE=y
# default:
CONFIG_ESP_SYSTEM_CHECK_INT_LEVEL_4=y
# default:
CONFIG_ESP_SYSTEM_HW_STACK_GUARD=y
# default:
CONFIG_ESP_SYSTEM_BBPLL_RECALIB=y
# default:
CONFIG_ESP_SYSTEM_HW_PC_RECORD=y
# end of ESP System Settings

#
# IPC (Inter-Processor Call)
#
# default:
CONFIG_ESP_IPC_TASK_STACK_SIZE=1024
# end of IPC (Inter-Processor Call)

#
# ESP Timer (High Resolution Timer)
#
# default:
CONFIG_ESP_TIMER_IN_IRAM=y
# default:
# CONFIG_ESP_TIMER_PROFILING is not set
# default:
CONFIG_ESP_TIME_FUNCS_USE_RTC_TIMER=y
# default:
CONFIG_ESP_TIME_FUNCS_USE_ESP_TIMER=y
# default:
CONFIG_ESP_TIMER_TASK_STACK_SIZE=3584
# default:
CONFIG_ESP_TIMER_INTERRUPT_LEVEL=1
# default:
# CONFIG_ESP_TIMER_SHOW_EXPERIMENTAL is not set
# default:
CONFIG_ESP_TIMER_TASK_AFFINITY=0x0
# default:
CONFIG_ESP_TIMER_TASK_AFFINITY_CPU0=y
# default:
CONFIG_ESP_TIMER_ISR_AFFINITY_CPU0=y
# default:
# CONFIG_ESP_TIMER_SUPPORTS_ISR_DISPATCH_METHOD is not set
# default:
CONFIG_ESP_TIMER_IMPL_SYSTIMER=y
# end of ESP Timer (High Resolution Timer)

#
# FreeRTOS
#

#
# Kernel
#
# default:
# CONFIG_FREERTOS_SMP is not set
# default:
CONFIG_FREERTOS_UNICORE=y
# default:
CONFIG_FREERTOS_HZ=100
# default:
CONFIG_FREERTOS_OPTIMIZED_SCHEDULER=y
# default:
# CONFIG_FREERTOS_CHECK_STACKOVERFLOW_NONE is not set
# default:
# CONFIG_FREERTOS_CHECK_STACKOVERFLOW_PTRVAL is not set
# default:
CONFIG_FREERTOS_CHECK_STACKOVERFLOW_CANARY=y
# default:
CONFIG_FREERTOS_THREAD_LOCAL_STORAGE_POINTERS=1
# default:
CONFIG_FREERTOS_IDLE_TASK_STACKSIZE=1536
# default:
# CONFIG_FREERTOS_USE_IDLE_HOOK is not set
# default:
# CONFIG_FREERTOS_USE_TICK_HOOK is not set
# default:
CONFIG_FREERTOS_MAX_TASK_NAME_LEN=16
# default:
# CONFIG_FREERTOS_ENABLE_BACKWARD_COMPATIBILITY is not set
# default:
CONFIG_FREERTOS_USE_TIMERS=y
# default:
CONFIG_FREERTOS_TIMER_SERVICE_TASK_NAME="Tmr Svc"
# default:
# CONFIG_FREERTOS_TIMER_TASK_AFFINITY_CPU0 is not set
# default:
CONFIG_FREERTOS_TIMER_TASK_NO_AFFINITY=y
# default:
CONFIG_FREERTOS_TIMER_SERVICE_TASK_CORE_AFFINITY=0x7FFFFFFF
# default:
CONFIG_FREERTOS_TIMER_TASK_PRIORITY=1
# default:
CONFIG_FREERTOS_TIMER_TASK_STACK_DEPTH=2048
# default:
CONFIG_FREERTOS_TIMER_QUEUE_LENGTH=10
# default:
CONFIG_FREERTOS_QUEUE_REGISTRY_SIZE=0
# default:
CONFIG_FREERTOS_TASK_NOTIFICATION_ARRAY_ENTRIES=1
# default:
# CONFIG_FREERTOS_USE_TRACE_FACILITY is not set
# default:
# CONFIG_FREERTOS_USE_LIST_DATA_INTEGRITY_CHECK_BYTES is not set
# default:
# CONFIG_FREERTOS_GENERATE_RUN_TIME_STATS is not set
# default:
# CONFIG_FREERTOS_USE_APPLICATION_TASK_TAG is not set
# end of Kernel

#
# Port
#
# default:
# CONFIG_FREERTOS_WATCHPOINT_END_OF_STACK is not set
# default:
CONFIG_FREERTOS_TLSP_DELETION_CALLBACKS=y
# default:
# CONFIG_FREERTOS_TASK_PRE_DELETION_HOOK is not set
# default:
CONFIG_FREERTOS_CHECK_MUTEX_GIVEN_BY_OWNER=y
# default:
CONFIG_FREERTOS_ISR_STACKSIZE=1536
# default:
CONFIG_FREERTOS_INTERRUPT_BACKTRACE=y
# default:
CONFIG_FREERTOS_TICK_SUPPORT_SYSTIMER=y
# default:
CONFIG_FREERTOS_CORETIMER_SYSTIMER_LVL1=y
# default:
# CONFIG_FREERTOS_CORETIMER_SYSTIMER_LVL3 is not set
# default:
CONFIG_FREERTOS_SYSTICK_USES_SYSTIMER=y
# default:
# CONFIG_FREERTOS_IN_IRAM is not set
# default:
# CONFIG_FREERTOS_CHECK_PORT_CRITICAL_COMPLIANCE is not set
# end of Port

#
# Extra
#
# end of Extra

# default:
CONFIG_FREERTOS_PORT=y
# default:
CONFIG_FREERTOS_NO_AFFINITY=0x7FFFFFFF
# default:
CONFIG_FREERTOS_SUPPORT_STATIC_ALLOCATION=y
# default:
CONFIG_FREERTOS_DEBUG_OCDAWARE=y
# default:
CONFIG_FREERTOS_NUMBER_OF_CORES=1
# end of FreeRTOS

#
# Hardware Abstraction Layer (HAL) and Low Level (LL)
#
# default:
CONFIG_HAL_ASSERTION_EQUALS_SYSTEM=y
# default:
# CONFIG_HAL_ASSERTION_DISABLE is not set
# default:
CONFIG_HAL_DEFAULT_ASSERTION_LEVEL=0
# default:
CONFIG_HAL_SYSTIMER_USE_ROM_IMPL=y
# default:
CONFIG_HAL_WDT_USE_ROM_IMPL=y
# default:
CONFIG_HAL_GPIO_USE_ROM_IMPL=y
# end of Hardware Abstraction Layer (HAL) and Low Level (LL)

#
# Heap memory debugging
#
# default:
CONFIG_HEAP_POISONING_DISABLED=y
# default:
# CONFIG_HEAP_POISONING_LIGHT is not set
# default:
# CONFIG_HEAP_POISONING_COMPREHENSIVE is not set
# default:
CONFIG_HEAP_TRACING_OFF=y
# default:
# CONFIG_HEAP_TRACING_STANDALONE is not set
# default:
# CONFIG_HEAP_TRACING_TOHOST is not set
# default:
# CONFIG_HEAP_USE_HOOKS is not set
# default:
# CONFIG_HEAP_TASK_TRACKING is not set
# default:
# CONFIG_HEAP_ABORT_WHEN_ALLOCATION_FAILS is not set
# default:
CONFIG_HEAP_TLSF_USE_ROM_IMPL=y
# default:
# CONFIG_HEAP_PLACE_FUNCTION_INTO_FLASH is not set
# end of Heap memory debugging

#
# Log
#
# default:
CONFIG_LOG_VERSION_1=y
# default:
# CONFIG_LOG_VERSION_2 is not set
# default:
CONFIG_LOG_VERSION=1

#
# Log Level
#
# CONFIG_LOG_DEFAULT_LEVEL_NONE is not set
CONFIG_LOG_DEFAULT_LEVEL_ERROR=y
# CONFIG_LOG_DEFAULT_LEVEL_WARN is not set
# CONFIG_LOG_DEFAULT_LEVEL_INFO is not set
# CONFIG_LOG_DEFAULT_LEVEL_DEBUG is not set
# CONFIG_LOG_DEFAULT_LEVEL_VERBOSE is not set
# default:
CONFIG_LOG_DEFAULT_LEVEL=1
# default:
CONFIG_LOG_MAXIMUM_EQUALS_DEFAULT=y
# default:
# CONFIG_LOG_MAXIMUM_LEVEL_WARN is not set
# default:
# CONFIG_LOG_MAXIMUM_LEVEL_INFO is not set
# default:
# CONFIG_LOG_MAXIMUM_LEVEL_DEBUG is not set
# default:
# CONFIG_LOG_MAXIMUM_LEVEL_VERBOSE is not set
# default:
CONFIG_LOG_MAXIMUM_LEVEL=1

#
# Level Settings
#
# default:
# CONFIG_LOG_MASTER_LEVEL is not set
# default:
CONFIG_LOG_DYNAMIC_LEVEL_CONTROL=y
# default:
# CONFIG_LOG_TAG_LEVEL_IMPL_NONE is not set
# default:
# CONFIG_LOG_TAG_LEVEL_IMPL_LINKED_LIST is not set
# default:
CONFIG_LOG_TAG_LEVEL_IMPL_CACHE_AND_LINKED_LIST=y
# default:
# CONFIG_LOG_TAG_LEVEL_CACHE_ARRAY is not set
# default:
CONFIG_LOG_TAG_LEVEL_CACHE_BINARY_MIN_HEAP=y
# default:
CONFIG_LOG_TAG_LEVEL_IMPL_CACHE_SIZE=31
# end of Level Settings
# end of Log Level

#
# Format
#
# default:
# CONFIG_LOG_COLORS is not set
# default:
CONFIG_LOG_TIMESTAMP_SOURCE_RTOS=y
# default:
# CONFIG_LOG_TIMESTAMP_SOURCE_SYSTEM is not set
# end of Format

#
# Settings
#
# default:
CONFIG_LOG_MODE_TEXT_EN=y
# default:
CONFIG_LOG_MODE_TEXT=y
# end of Settings

# default:
CONFIG_LOG_IN_IRAM=y
# end of Log

#
# mbedTLS
#

#
# Core Configuration
#
# default:
CONFIG_MBEDTLS_VER_4_X_SUPPORT=y
# default:
# CONFIG_MBEDTLS_COMPILER_OPTIMIZATION_NONE is not set
# default:
CONFIG_MBEDTLS_COMPILER_OPTIMIZATION_SIZE=y
# default:
# CONFIG_MBEDTLS_COMPILER_OPTIMIZATION_PERF is not set
# default:
CONFIG_MBEDTLS_FS_IO=y
# default:
CONFIG_MBEDTLS_THREADING_C=y
# default:
# CONFIG_MBEDTLS_THREADING_ALT is not set
# default:
CONFIG_MBEDTLS_THREADING_PTHREAD=y
# default:
CONFIG_MBEDTLS_ERROR_STRINGS=y
# default:
CONFIG_MBEDTLS_VERSION_C=y
# default:
CONFIG_MBEDTLS_HAVE_TIME=y
# default:
# CONFIG_MBEDTLS_PLATFORM_TIME_ALT is not set
# default:
# CONFIG_MBEDTLS_HAVE_TIME_DATE is not set
# default:
CONFIG_MBEDTLS_INTERNAL_MEM_ALLOC=y
# default:
# CONFIG_MBEDTLS_DEFAULT_MEM_ALLOC is not set
# default:
# CONFIG_MBEDTLS_CUSTOM_MEM_ALLOC is not set
# default:
CONFIG_MBEDTLS_ASYMMETRIC_CONTENT_LEN=y
# default:
CONFIG_MBEDTLS_SSL_IN_CONTENT_LEN=16384
# default:
CONFIG_MBEDTLS_SSL_OUT_CONTENT_LEN=4096
# default:
# CONFIG_MBEDTLS_DYNAMIC_BUFFER is not set
# default:
# CONFIG_MBEDTLS_VERSION_FEATURES is not set
# default:
# CONFIG_MBEDTLS_DEBUG is not set
# default:
CONFIG_MBEDTLS_SELF_TEST=y
# end of Core Configuration

#
# Certificates
#
CONFIG_MBEDTLS_X509_USE_C=y
# default:
CONFIG_MBEDTLS_PEM_PARSE_C=y
# default:
CONFIG_MBEDTLS_PEM_WRITE_C=y
# default:
CONFIG_MBEDTLS_PK_C=y
# default:
CONFIG_MBEDTLS_PK_PARSE_C=y
# default:
CONFIG_MBEDTLS_PK_WRITE_C=y
# default:
# CONFIG_MBEDTLS_X509_REMOVE_INFO is not set
# default:
CONFIG_MBEDTLS_X509_CRL_PARSE_C=y
# default:
CONFIG_MBEDTLS_X509_CRT_PARSE_C=y
# default:
CONFIG_MBEDTLS_X509_CSR_PARSE_C=y
# default:
# CONFIG_MBEDTLS_X509_CREATE_C is not set
# default:
CONFIG_MBEDTLS_X509_RSASSA_PSS_SUPPORT=y
# default:
# CONFIG_MBEDTLS_X509_TRUSTED_CERT_CALLBACK is not set
# default:
CONFIG_MBEDTLS_ASN1_PARSE_C=y
# default:
CONFIG_MBEDTLS_ASN1_WRITE_C=y
# CONFIG_MBEDTLS_CERTIFICATE_BUNDLE is not set
# default:
# CONFIG_MBEDTLS_ALLOW_WEAK_CERTIFICATE_VERIFICATION is not set
# end of Certificates

# default:
CONFIG_MBEDTLS_TLS_ENABLED=y

#
# TLS Protocol Configuration
#
# default:
CONFIG_MBEDTLS_SSL_PROTO_TLS1_2=y
# default:
# CONFIG_MBEDTLS_SSL_PROTO_TLS1_3 is not set
# default:
# CONFIG_MBEDTLS_SSL_PROTO_GMTSSL1_1 is not set
# default:
CONFIG_MBEDTLS_TLS_SERVER=y
# default:
CONFIG_MBEDTLS_TLS_CLIENT=y
# default:
CONFIG_MBEDTLS_TLS_SERVER_AND_CLIENT=y
# default:
# CONFIG_MBEDTLS_TLS_SERVER_ONLY is not set
# default:
# CONFIG_MBEDTLS_TLS_CLIENT_ONLY is not set
# default:
# CONFIG_MBEDTLS_TLS_DISABLED is not set
# default:
# CONFIG_MBEDTLS_SSL_KEEP_PEER_CERTIFICATE is not set
# default:
# CONFIG_MBEDTLS_SSL_CONTEXT_SERIALIZATION is not set
# default:
CONFIG_MBEDTLS_SSL_CACHE_C=y
# default:
CONFIG_MBEDTLS_SSL_ALL_ALERT_MESSAGES=y

#
# TLS Key Exchange Configuration
#
# default:
# CONFIG_MBEDTLS_PSK_MODES is not set
# default:
CONFIG_MBEDTLS_KEY_EXCHANGE_RSA=y
# default:
CONFIG_MBEDTLS_KEY_EXCHANGE_ELLIPTIC_CURVE=y
# default:
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDHE_RSA=y
# default:
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDHE_ECDSA=y
# end of TLS Key Exchange Configuration

# default:
CONFIG_MBEDTLS_SSL_SERVER_NAME_INDICATION=y
# default:
CONFIG_MBEDTLS_SSL_ALPN=y
# default:
CONFIG_MBEDTLS_SSL_MAX_FRAGMENT_LENGTH=y
# default:
# CONFIG_MBEDTLS_SSL_VARIABLE_BUFFER_LENGTH is not set
# default:
CONFIG_MBEDTLS_SSL_RENEGOTIATION=y
# default:
CONFIG_MBEDTLS_CLIENT_SSL_SESSION_TICKETS=y
# default:
CONFIG_MBEDTLS_SERVER_SSL_SESSION_TICKETS=y
# default:
# CONFIG_MBEDTLS_SSL_KEYING_MATERIAL_EXPORT is not set
# end of TLS Protocol Configuration

# default:
# CONFIG_MBEDTLS_SSL_PROTO_DTLS is not set

#
# Symmetric Ciphers
#
# default:
CONFIG_MBEDTLS_AES_C=y
# default:
# CONFIG_MBEDTLS_CAMELLIA_C is not set
# default:
# CONFIG_MBEDTLS_ARIA_C is not set
# default:
# CONFIG_MBEDTLS_DES_C is not set
# default:
CONFIG_MBEDTLS_CCM_C=y
# default:
CONFIG_MBEDTLS_CIPHER_MODE_CBC=y
# default:
CONFIG_MBEDTLS_CIPHER_MODE_CFB=y
# default:
CONFIG_MBEDTLS_CIPHER_MODE_CTR=y
# default:
CONFIG_MBEDTLS_CIPHER_MODE_OFB=y
# default:
CONFIG_MBEDTLS_CIPHER_MODE_XTS=y
# default:
CONFIG_MBEDTLS_GCM_C=y
# default:
# CONFIG_MBEDTLS_NIST_KW_C is not set
# default:
CONFIG_MBEDTLS_AES_ROM_TABLES=y
# default:
# CONFIG_MBEDTLS_AES_FEWER_TABLES is not set
# default:
# CONFIG_MBEDTLS_AES_ONLY_128_BIT_KEY_LENGTH is not set
# default:
CONFIG_MBEDTLS_CMAC_C=y
# end of Symmetric Ciphers

#
# Asymmetric Ciphers
#
# default:
CONFIG_MBEDTLS_BIGNUM_C=y
# default:
CONFIG_MBEDTLS_RSA_C=y
# default:
CONFIG_MBEDTLS_ECP_C=y

#
# Supported Curves
#
# default:
CONFIG_MBEDTLS_ECP_DP_SECP256R1_ENABLED=y
# default:
CONFIG_MBEDTLS_ECP_DP_SECP384R1_ENABLED=y
# default:
CONFIG_MBEDTLS_ECP_DP_SECP521R1_ENABLED=y
# default:
CONFIG_MBEDTLS_ECP_DP_SECP256K1_ENABLED=y
# default:
CONFIG_MBEDTLS_ECP_DP_BP256R1_ENABLED=y
# default:
CONFIG_MBEDTLS_ECP_DP_BP384R1_ENABLED=y
# default:
CONFIG_MBEDTLS_ECP_DP_BP512R1_ENABLED=y
# default:
CONFIG_MBEDTLS_ECP_DP_CURVE25519_ENABLED=y
# end of Supported Curves

#
# Elliptic Curve Ciphers Configuration
#
# default:
CONFIG_MBEDTLS_ECP_NIST_OPTIM=y
# default:
# CONFIG_MBEDTLS_ECP_FIXED_POINT_OPTIM is not set
# default:
# CONFIG_MBEDTLS_DHM_C is not set
# default:
CONFIG_MBEDTLS_ECDH_C=y
# default:
# CONFIG_MBEDTLS_ECJPAKE_C is not set
# default:
CONFIG_MBEDTLS_ECDSA_C=y
# default:
CONFIG_MBEDTLS_PK_PARSE_EC_EXTENDED=y
# default:
CONFIG_MBEDTLS_PK_PARSE_EC_COMPRESSED=y
# default:
CONFIG_MBEDTLS_ECDSA_DETERMINISTIC=y
# default:
# CONFIG_MBEDTLS_ECP_RESTARTABLE is not set
# end of Elliptic Curve Ciphers Configuration
# end of Asymmetric Ciphers

#
# Hash functions
#
# default:
# CONFIG_MBEDTLS_RIPEMD160_C is not set
# default:
CONFIG_MBEDTLS_MD_C=y
# default:
CONFIG_MBEDTLS_MD5_C=y
# default:
CONFIG_MBEDTLS_SHA1_C=y
# default:
# CONFIG_MBEDTLS_SHA224_C is not set
# default:
CONFIG_MBEDTLS_SHA256_C=y
# default:
CONFIG_MBEDTLS_SHA384_C=y
# default:
CONFIG_MBEDTLS_SHA512_C=y
# default:
# CONFIG_MBEDTLS_SHA3_C is not set
# default:
CONFIG_MBEDTLS_ROM_MD5=y
# end of Hash functions

#
# Hardware Acceleration
#
# default:
CONFIG_MBEDTLS_HARDWARE_ECC=y
# default:
CONFIG_MBEDTLS_ECC_OTHER_CURVES_SOFT_FALLBACK=y
# default:
CONFIG_MBEDTLS_HARDWARE_SHA=y
# default:
CONFIG_MBEDTLS_HARDWARE_MPI=y
# default:
CONFIG_MBEDTLS_LARGE_KEY_SOFTWARE_MPI=y
# default:
CONFIG_MBEDTLS_MPI_USE_INTERRUPT=y
# default:
CONFIG_MBEDTLS_MPI_INTERRUPT_LEVEL=0
# default:
CONFIG_MBEDTLS_HARDWARE_AES=y
# default:
# CONFIG_MBEDTLS_AES_SOFT_FALLBACK is not set
# default:
CONFIG_MBEDTLS_GCM_SUPPORT_NON_AES_CIPHER=y
# default:
CONFIG_MBEDTLS_AES_USE_INTERRUPT=y
# default:
CONFIG_MBEDTLS_AES_INTERRUPT_LEVEL=0
# default:
CONFIG_MBEDTLS_AES_HW_SMALL_DATA_LEN_OPTIM=y
# default:
# CONFIG_MBEDTLS_ATCA_HW_ECDSA_SIGN is not set
# default:
# CONFIG_MBEDTLS_ATCA_HW_ECDSA_VERIFY is not set
# default:
CONFIG_MBEDTLS_HARDWARE_RSA_DS_PERIPHERAL=y
# end of Hardware Acceleration

#
# Entropy and Random Number Generation
#
# default:
# CONFIG_MBEDTLS_ENTROPY_FORCE_SHA256 is not set
# default:
CONFIG_MBEDTLS_CTR_DRBG_C=y
# default:
CONFIG_MBEDTLS_HMAC_DRBG_C=y
# end of Entropy and Random Number Generation

#
# Encoding/Decoding
#
# default:
CONFIG_MBEDTLS_BASE64_C=y
# default:
CONFIG_MBEDTLS_PKCS5_C=y
# default:
CONFIG_MBEDTLS_PKCS7_C=y
# default:
CONFIG_MBEDTLS_PKCS1_V15=y
# default:
CONFIG_MBEDTLS_PKCS1_V21=y
# end of Encoding/Decoding

#
# Stream Cipher
#
# default:
# CONFIG_MBEDTLS_CHACHA20_C is not set
# end of Stream Cipher
# end of mbedTLS

#
# PThreads
#
# default:
CONFIG_PTHREAD_TASK_PRIO_DEFAULT=5
# default:
CONFIG_PTHREAD_TASK_STACK_SIZE_DEFAULT=3072
# default:
CONFIG_PTHREAD_STACK_MIN=768
# default:
CONFIG_PTHREAD_TASK_CORE_DEFAULT=-1
# default:
CONFIG_PTHREAD_TASK_NAME_DEFAULT="pthread"
# end of PThreads

#
# MMU Config
#
# default:
CONFIG_MMU_PAGE_SIZE_64KB=y
# default:
CONFIG_MMU_PAGE_MODE="64KB"
# default:
CONFIG_MMU_PAGE_SIZE=0x10000
# end of MMU Config

#
# Main Flash configuration
#

#
# SPI Flash behavior when brownout
#
# default:
CONFIG_SPI_FLASH_BROWNOUT_RESET_XMC=y
# default:
CONFIG_SPI_FLASH_BROWNOUT_RESET=y
# end of SPI Flash behavior when brownout

#
# Optional and Experimental Features (READ DOCS FIRST)
#

#
# Features here require specific hardware (READ DOCS FIRST!)
#
# default:
# CONFIG_SPI_FLASH_AUTO_SUSPEND is not set
# default:
CONFIG_SPI_FLASH_SUSPEND_TSUS_VAL_US=50
# default:
# CONFIG_SPI_FLASH_FORCE_ENABLE_XMC_C_SUSPEND is not set
# default:
# CONFIG_SPI_FLASH_FORCE_ENABLE_C6_H2_SUSPEND is not set
# default:
CONFIG_SPI_FLASH_PLACE_FUNCTIONS_IN_IRAM=y
# end of Optional and Experimental Features (READ DOCS FIRST)
# end of Main Flash configuration

#
# SPI Flash driver
#
# default:
# CONFIG_SPI_FLASH_VERIFY_WRITE is not set
# default:
# CONFIG_SPI_FLASH_ENABLE_COUNTERS is not set
# default:
# CONFIG_SPI_FLASH_ROM_IMPL is not set
# default:
CONFIG_SPI_FLASH_DANGEROUS_WRITE_ABORTS=y
# default:
# CONFIG_SPI_FLASH_DANGEROUS_WRITE_FAILS is not set
# default:
# CONFIG_SPI_FLASH_DANGEROUS_WRITE_ALLOWED is not set
# default:
# CONFIG_SPI_FLASH_BYPASS_BLOCK_ERASE is not set
# default:
CONFIG_SPI_FLASH_YIELD_DURING_ERASE=y
# default:
CONFIG_SPI_FLASH_ERASE_YIELD_DURATION_MS=20
# default:
CONFIG_SPI_FLASH_ERASE_YIELD_TICKS=1
# default:
CONFIG_SPI_FLASH_WRITE_CHUNK_SIZE=8192
# default:
# CONFIG_SPI_FLASH_SIZE_OVERRIDE is not set
# default:
# CONFIG_SPI_FLASH_CHECK_ERASE_TIMEOUT_DISABLED is not set
# default:
# CONFIG_SPI_FLASH_OVERRIDE_CHIP_DRIVER_LIST is not set

#
# Auto-detect flash chips
#
# default:
CONFIG_SPI_FLASH_VENDOR_XMC_SUPPORT_ENABLED=y
# default:
CONFIG_SPI_FLASH_VENDOR_GD_SUPPORT_ENABLED=y
# default:
# CONFIG_SPI_FLASH_SUPPORT_ISSI_CHIP is not set
# default:
# CONFIG_SPI_FLASH_SUPPORT_MXIC_CHIP is not set
# default:
CONFIG_SPI_FLASH_SUPPORT_GD_CHIP=y
# default:
# CONFIG_SPI_FLASH_SUPPORT_WINBOND_CHIP is not set
# default:
# CONFIG_SPI_FLASH_SUPPORT_BOYA_CHIP is not set
# default:
# CONFIG_SPI_FLASH_SUPPORT_TH_CHIP is not set
# end of Auto-detect flash chips

# default:
CONFIG_SPI_FLASH_ENABLE_ENCRYPTED_READ_WRITE=y
# end of SPI Flash driver

#
# Virtual file system
#
# default:
CONFIG_VFS_SUPPORT_IO=y
# default:
CONFIG_VFS_SUPPORT_DIR=y
# default:
CONFIG_VFS_SUPPORT_SELECT=y
# default:
CONFIG_VFS_SUPPRESS_SELECT_DEBUG_OUTPUT=y
# default:
# CONFIG_VFS_SELECT_IN_RAM is not set
# default:
# CONFIG_VFS_SUPPORT_TERMIOS is not set
# default:
CONFIG_VFS_MAX_COUNT=8

#
# Host File System I/O (Semihosting)
#
# default:
CONFIG_VFS_SEMIHOSTFS_MAX_MOUNT_POINTS=1
# end of Host File System I/O (Semihosting)

# default:
CONFIG_VFS_INITIALIZE_DEV_NULL=y
# end of Virtual file system
# end of Component config

# default:
# CONFIG_IDF_EXPERIMENTAL_FEATURES is not set

# Deprecated options for backward compatibility
# CONFIG_APP_BUILD_TYPE_ELF_RAM is not set
# CONFIG_NO_BLOBS is not set
# CONFIG_APP_ROLLBACK_ENABLE is not set
# CONFIG_BOOTLOADER_COMPILER_OPTIMIZATION_NONE is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_NONE is not set
CONFIG_LOG_BOOTLOADER_LEVEL_ERROR=y
# CONFIG_LOG_BOOTLOADER_LEVEL_WARN is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_INFO is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_DEBUG is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_VERBOSE is not set
CONFIG_LOG_BOOTLOADER_LEVEL=1
# CONFIG_FLASH_ENCRYPTION_ENABLED is not set
# CONFIG_FLASHMODE_QIO is not set
# CONFIG_FLASHMODE_QOUT is not set
CONFIG_FLASHMODE_DIO=y
# CONFIG_FLASHMODE_DOUT is not set
CONFIG_MONITOR_BAUD=115200
# CONFIG_OPTIMIZATION_LEVEL_DEBUG is not set
# CONFIG_COMPILER_OPTIMIZATION_LEVEL_DEBUG is not set
# CONFIG_COMPILER_OPTIMIZATION_DEFAULT is not set
CONFIG_OPTIMIZATION_LEVEL_RELEASE=y
CONFIG_COMPILER_OPTIMIZATION_LEVEL_RELEASE=y
# CONFIG_OPTIMIZATION_ASSERTIONS_ENABLED is not set
# CONFIG_OPTIMIZATION_ASSERTIONS_SILENT is not set
CONFIG_OPTIMIZATION_ASSERTIONS_DISABLED=y
CONFIG_OPTIMIZATION_ASSERTION_LEVEL=0
# CONFIG_CXX_EXCEPTIONS is not set
CONFIG_STACK_CHECK_NONE=y
# CONFIG_STACK_CHECK_NORM is not set
# CONFIG_STACK_CHECK_STRONG is not set
# CONFIG_STACK_CHECK_ALL is not set
# CONFIG_WARN_WRITE_STRINGS is not set
# CONFIG_ESP_SYSTEM_PD_FLASH is not set
CONFIG_PERIPH_CTRL_FUNC_IN_IRAM=y
CONFIG_BROWNOUT_DET=y
CONFIG_BROWNOUT_DET_LVL_SEL_7=y
# CONFIG_BROWNOUT_DET_LVL_SEL_6 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_5 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_4 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_3 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_2 is not set
CONFIG_BROWNOUT_DET_LVL=7
CONFIG_ESP_SYSTEM_BROWNOUT_INTR=y
CONFIG_NEWLIB_STDOUT_LINE_ENDING_CRLF=y
# CONFIG_NEWLIB_STDOUT_LINE_ENDING_LF is not set
# CONFIG_NEWLIB_STDOUT_LINE_ENDING_CR is not set
# CONFIG_NEWLIB_STDIN_LINE_ENDING_CRLF is not set
# CONFIG_NEWLIB_STDIN_LINE_ENDING_LF is not set
CONFIG_NEWLIB_STDIN_LINE_ENDING_CR=y
CONFIG_NEWLIB_TIME_SYSCALL_USE_RTC_HRT=y
# CONFIG_NEWLIB_TIME_SYSCALL_USE_RTC is not set
# CONFIG_NEWLIB_TIME_SYSCALL_USE_HRT is not set
# CONFIG_NEWLIB_TIME_SYSCALL_USE_NONE is not set
CONFIG_ESP_SYSTEM_PM_POWER_DOWN_CPU=y
# CONFIG_CONSOLE_UART_DEFAULT is not set
# CONFIG_CONSOLE_UART_CUSTOM is not set
# CONFIG_CONSOLE_UART_NONE is not set
# CONFIG_ESP_CONSOLE_UART_NONE is not set
CONFIG_CONSOLE_UART_NUM=-1
CONFIG_ESP_SYSTEM_PMP_IDRAM_SPLIT=y
CONFIG_ESP_SYSTEM_MEMPROT_FEATURE_VIA_TEE=y
CONFIG_ESP_SYSTEM_MEMPROT_FEATURE=y
# CONFIG_ESP_SYSTEM_PMP_LP_CORE_RESERVE_MEM_EXECUTABLE is not set
CONFIG_SYSTEM_EVENT_QUEUE_SIZE=32
CONFIG_SYSTEM_EVENT_TASK_STACK_SIZE=2304
CONFIG_MAIN_TASK_STACK_SIZE=3584
CONFIG_INT_WDT=y
CONFIG_INT_WDT_TIMEOUT_MS=300
CONFIG_TASK_WDT=y
CONFIG_ESP_TASK_WDT=y
# CONFIG_TASK_WDT_PANIC is not set
CONFIG_TASK_WDT_TIMEOUT_S=5
CONFIG_TASK_WDT_CHECK_IDLE_TASK_CPU0=y
# CONFIG_ESP32_DEBUG_STUBS_ENABLE is not set
CONFIG_IPC_TASK_STACK_SIZE=1024
CONFIG_TIMER_TASK_STACK_SIZE=3584
CONFIG_TIMER_TASK_PRIORITY=1
CONFIG_TIMER_TASK_STACK_DEPTH=2048
CONFIG_TIMER_QUEUE_LENGTH=10
# CONFIG_ENABLE_STATIC_TASK_CLEAN_UP_HOOK is not set
CONFIG_ESP32_PTHREAD_TASK_PRIO_DEFAULT=5
CONFIG_ESP32_PTHREAD_TASK_STACK_SIZE_DEFAULT=3072
CONFIG_ESP32_PTHREAD_STACK_MIN=768
CONFIG_ESP32_PTHREAD_TASK_CORE_DEFAULT=-1
CONFIG_ESP32_PTHREAD_TASK_NAME_DEFAULT="pthread"
CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_ABORTS=y
# CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_FAILS is not set
# CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_ALLOWED is not set
CONFIG_SUPPRESS_SELECT_DEBUG_OUTPUT=y
# CONFIG_SUPPORT_TERMIOS is not set
CONFIG_SEMIHOSTFS_MAX_MOUNT_POINTS=1
# End of deprecated options