Documentation related to auto ventilation

[michaelarnauts]

I've noticed 225 and 226 are related to the automatic mode.

My ventilation was running with a low fan speed, and in auto mode with humidity protection active.

Detected a high humidity (SENSOR mode active). The fan started spinning high.
225 = 2
226 = 300

Fell back to normal mode.
225 = 1
226 = 100

[michaelarnauts]

@decontamin4t0R have you played with these values?

• Maybe 226 / 100 is the current fan mode? Strange that the value is *100.
• 225 might be a status mode? 1 = NORMAL, 2 = SENSOR?

[decontamin4t0R]

I think that 225 indicates that one of the protections is active, and 226 is either the protection itself or the sensor which caused the protection to go active... Do you still have the value of 230 handy? They are the ventilation constraints, so the bit 27 should be 1...

[michaelarnauts]

I wasn't logging 230 unfortunately. How did you get this number, and how did you found out about the bits? Have you perhaps documented this somewhere?

[michaelarnauts]

230 isn't even in the RPDO_TYPE_MAP, so I don't know the size. I've created that map some time ago by using the app and going trough most menus and capturing what each sensor size was.

[decontamin4t0R]

The App contains the 230 as ventilation config constraints, UINT64, bitfield. The 27 is the bit for either VentConfConstraintHumidityProtectionLong or VentConfConstraintHumidityProtection.
For some more PDOs, you can check the https://github.com/decontamin4t0R/zcan/blob/master/mapping2.py although im sure it does not contain all of them

[decontamin4t0R]

oops, just checked my notes again:
225 DISABLED/ACTIVE/OVERRULING
226???, UINT16
227, UINT8, Unsigned Percentage bypass state
228, UINT8, Unsigned Percentage UnitStatus.FrostProtectionUnbalance

[michaelarnauts]

The App contains the 230 as ventilation config constraints, UINT64, bitfield. The 27 is the bit for either VentConfConstraintHumidityProtectionLong or VentConfConstraintHumidityProtection.
For some more PDOs, you can check the https://github.com/decontamin4t0R/zcan/blob/master/mapping2.py although im sure it does not contain all of them

Did you succeed in decompiling of the app? I've tried this approach, and it gave me the protocol buffers file, but I could never find the PDO ID's.

[decontamin4t0R]

yeah... you can just take the decompiled source, its obfuscated but i was able to give the classes and packages distinguishable names, so you know that the class c072a or so is used there etc.

[decontamin4t0R]

Yes, just confirmed. When you set humidity protection to on or to autoonly and have the ventilation in auto, 225 is 1. 0 if humidity protection = disabled or autoonly and manual.

[HalliHalloSchatz]

Hello,

I have a "good" deobfuscated set off an older app. My problem ist, that I am not a programmer. I can not find the correct class, where the description is.

[michaelarnauts]

I've tried a lot of tools to deobfuscate the app, but due to a lot of setters and getters, and passing around of objects, it's not to easy to understand it.

I recently took a new look at it, and there is one class with all the pdo's, but these pdos tend to get replaced with constants from the java libs.

[decontamin4t0R]

If you search for something or have a question, just ask, that is probably easier than looking into the code and getting a hang of it

[HalliHalloSchatz]

I can agree to:
225 = 1, when HumProtection is on, 2 when HumProtection overwrite the normal condition
226 = 100 (FanMode 1), 200 (FanMode 2) and 300 (FanMode 3) all value between the hundrets 100-200 and 200-300 are modulated the ventilation. I can follow these with the airflow-sensor.

My Operation Idea:
I use a central vacuum cleaner, that blow out the air from my house. I have a really negativ airpressure. Now I will activate the SupplyOnlyFan Mode to blow in the air. When the FrostProtection function is regulated the ventilation down until 50%, I will power down the vacuum cleaner. The FrostProtection is modulated the ventilator between 0% (Fan have full power) to 100% (Fans power down).
I have test these scenario manual on the display, and that works fine. Now I will do it automatically.

I search for the correct ventilation mode:
Auto / Manual / ManualUntil

SENSOR_OPERATING_MODE_BIS = 49
SENSOR_OPERATING_MODE = 56
shown -1

I found these in the file UnbalanceDetailFragment_ViewBinding.java:
seekBarUnbalance = ((AppCompatSeekBar)Attribute.getString(paramView, 2131559023, "field 'seekBarUnbalance'", AppCompatSeekBar.class));
unbalanceCurrentValue = ((TextView)Attribute.getString(paramView, 2131559022, "field 'unbalanceCurrentValue'", TextView.class));

I found these in the file VentControlDetailFragment_ViewBinding.java:
View localView = Attribute.getInstance(paramView, 2131558964, "field 'modeRow' and method 'rowModeClicked'");
modeRow = localView;
a = localView;
localView.setOnClickListener(new VentControlDetailFragment_ViewBinding.1(this, paramVentControlDetailFragment));
modeValue = ((TextView)Attribute.getString(paramView, 2131558965, "field 'modeValue'", TextView.class));
modePicker = ((NumberPicker)Attribute.getString(paramView, 2131558966, "field 'modePicker'", NumberPicker.class));

I will show on my central monitor these condition warnings:
I found these in file AlertController.java:
b.put(Integer.valueOf(62), new e(this, "Unbalance_ERR", true, new StringBuilder("Error.ComfoAirQ.Unbalance_ERR")));
b.put(Integer.valueOf(61), new e(this, "T_22_frost_ERR", false, new StringBuilder("Error.ComfoAirQ.T_22_frost_ERR")));
b.put(Integer.valueOf(77), new e(this, "Filter_alarm_flag", false, new StringBuilder("Error.ComfoAirQ.Filter_alarm_flag")));
b.put(Integer.valueOf(78), new e(this, "Filter_ext_ERR", false, new StringBuilder("Error.ComfoAirQ.Filter_ext_ERR")));
b.put(Integer.valueOf(79), new e(this, "Filter_warning_flag", false, new StringBuilder("Error.ComfoAirQ.Filter_warning_flag")));
b.put(Integer.valueOf(80), new e(this, "Standby_ERR", false, new StringBuilder("Error.ComfoAirQ.Standby_ERR")));

I found these lines in the file SensorVentDetailFragment_ViewBindings.java:
tempPassivePicker = ((NumberPicker)Attribute.getString(paramView, 2131558935, "field 'tempPassivePicker'", NumberPicker.class));
tempActivePicker = ((NumberPicker)Attribute.getString(paramView, 2131558938, "field 'tempActivePicker'", NumberPicker.class));
humComfortPicker = ((NumberPicker)Attribute.getString(paramView, 2131558941, "field 'humComfortPicker'", NumberPicker.class));
humProtectionPicker = ((NumberPicker)Attribute.getString(paramView, 2131558944, "field 'humProtectionPicker'", NumberPicker.class));
tempPassiveValue = ((TextView)Attribute.getString(paramView, 2131558934, "field 'tempPassiveValue'", TextView.class));
tempActiveValue = ((TextView)Attribute.getString(paramView, 2131558937, "field 'tempActiveValue'", TextView.class));
humComfortValue = ((TextView)Attribute.getString(paramView, 2131558940, "field 'humComfortValue'", TextView.class));
humProtectionValue = ((TextView)Attribute.getString(paramView, 2131558943, "field 'humProtectionValue'", TextView.class));

[decontamin4t0R]

My notes:

deactivate exhaust fan: (RMI: 0x8415 0601 0000 0000 FFFF FFFF 01)
    cansend can1 1F015057#00 84 15 06 01 00 00 00
    cansend can1 1F015057#81 00 FF FF FF FF 01
  remove "deactivate exhaust fan": (RMI: 0x85150601)
    cansend can1 1F011074#85 15 06 01
deactivate supply fan: (RMI: 0x8415 0701 0000 0000 FFFF FFFF 01)
    cansend can1 1F015057#00 84 15 07 01 00 00 00
    cansend can1 1F015057#81 00 FF FF FF FF 01
  remove "deactivate supply fan": (RMI: 0x85150701)
    cansend can1 1F011074#85 15 07 01
(you need to remove the spaces in the commands after #)
0x84: activate timer, 0x85: deactivate timer
0x15: Scheduling unit
0x06: Exhaustfan, 0x07: Supplyfan

for the unbalance bit, check pdo 230 at bit 62
and for the frost disbalance percentage, check PDO 228

[HalliHalloSchatz]

thank you.
I will add PDO 228. I have no idea, where I can check PDO 230... I am not a programmer, sorry. I will use the openhab_gw code for my tests.

I found in the file DescriptorProtos.java:
public static final class DescriptorProto
extends GeneratedMessage
implements DescriptorProtos.DescriptorProtoOrBuilder
{
public static final int ENUM_TYPE_FIELD_NUMBER = 4;
public static final int EXTENSION_FIELD_NUMBER = 6;
public static final int EXTENSION_RANGE_FIELD_NUMBER = 5;
public static final int FIELD_FIELD_NUMBER = 2;
public static final int NAME_FIELD_NUMBER = 1;
public static final int NESTED_TYPE_FIELD_NUMBER = 3;
public static final int ONEOF_DECL_FIELD_NUMBER = 8;
public static final int OPTIONS_FIELD_NUMBER = 7;
public static Parser PARSER = new AbstractParser()