QUINCY debug mode not working!

[steve64]

I'm trying to use the Quincy Pawn IDE 0.7.6974M
After compiled a simple hello.p with symbolic debugging and started the debug-mode execution, I got an error message in a dialog box:

Wxquincy Error
"Couldn't retrieve information about list control item 0"

[compuphase]

I cannot reproduce this error. I located the error message in the source code of wxWidgets for a list control. But there are several list controls in the program, so I do not know where to look.

Did you load the "hello.p" from the examples that come with Pawn, or a similar program that you wrote yourself. If it is your own version, can you copy it here, so that I can test with the exact same version as you.

[steve64]

Thanks for your feedback. The issue happens always since the second time I try to debug in a session (on my PC, Window 10) The sequence is: 1. start wxquincy.exe 2. open the "hello.p" example 3. run without debugging -> OK, it runs 4. run with debug (F5) -> OK, it steps on the code lines 5. run without debugging -> OK, it runs 6. run with debug (F5) -> KO, the error dialog appears (list control item 0) Note: since I do not have admin rights on this PC, I installed from pawn-4.1.7152.exe on another PC then copied the entire Pawn folder to this PC. Is there anything that the installer does besides extracting the Pawn folder ? (environment setting, registry, ...) By the way, also on the second PC (with proper auto-installation) I get exactly the same issue. Kind regards, Stefano

…

________________________________ Da: Thiadmer Riemersma ***@***.***> Inviato: sabato 27 luglio 2024 21:20 A: compuphase/pawn ***@***.***> Cc: steve64 ***@***.***>; Author ***@***.***> Oggetto: Re: [compuphase/pawn] QUINCY debug mode not working! (Issue #91) I cannot reproduce this error. I located the error message in the source code of wxWidgets for a list control. But there are several list controls in the program, so I do not know where to look. Did you load the "hello.p" from the examples that come with Pawn, or a similar program that you wrote yourself. If it is your own version, can you copy it here, so that I can test with the exact same version as you. — Reply to this email directly, view it on GitHub<#91 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AC2TQMTJI7WX6FNS37A43Z3ZOPXGNAVCNFSM6AAAAABLQVEBDKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJUGIZTENRRGI>. You are receiving this because you authored the thread.

[steve64]

Probably the list control triggering the error dialog on the second debug attempt is one of the bottom panels: Build, Messages or Watches. I do not see other list controls in the main GUI window. Regards, Stefano

…

________________________________ Da: Stefano Antoniazzi ***@***.***> Inviato: domenica 28 luglio 2024 09:05 A: compuphase/pawn ***@***.***>; compuphase/pawn ***@***.***> Cc: Author ***@***.***> Oggetto: R: [compuphase/pawn] QUINCY debug mode not working! (Issue #91) Thanks for your feedback. The issue happens always since the second time I try to debug in a session (on my PC, Window 10) The sequence is: 1. start wxquincy.exe 2. open the "hello.p" example 3. run without debugging -> OK, it runs 4. run with debug (F5) -> OK, it steps on the code lines 5. run without debugging -> OK, it runs 6. run with debug (F5) -> KO, the error dialog appears (list control item 0) Note: since I do not have admin rights on this PC, I installed from pawn-4.1.7152.exe on another PC then copied the entire Pawn folder to this PC. Is there anything that the installer does besides extracting the Pawn folder ? (environment setting, registry, ...) By the way, also on the second PC (with proper auto-installation) I get exactly the same issue. Kind regards, Stefano

________________________________ Da: Thiadmer Riemersma ***@***.***> Inviato: sabato 27 luglio 2024 21:20 A: compuphase/pawn ***@***.***> Cc: steve64 ***@***.***>; Author ***@***.***> Oggetto: Re: [compuphase/pawn] QUINCY debug mode not working! (Issue #91) I cannot reproduce this error. I located the error message in the source code of wxWidgets for a list control. But there are several list controls in the program, so I do not know where to look. Did you load the "hello.p" from the examples that come with Pawn, or a similar program that you wrote yourself. If it is your own version, can you copy it here, so that I can test with the exact same version as you. — Reply to this email directly, view it on GitHub<#91 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AC2TQMTJI7WX6FNS37A43Z3ZOPXGNAVCNFSM6AAAAABLQVEBDKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJUGIZTENRRGI>. You are receiving this because you authored the thread.

[steve64]

I just noticed that, after the error dialog, the step debugger seems to work.
So it seems just a matter of removing that annoying dialog.

Maybe the issue is in this code fragment inside QuincyFrame.cpp accessing the Watches list control?

if (DebugMode) {
    /* copy all rows in the watch log to the update list */
    LastWatchIndex = 0;
    WatchUpdateList.Clear();
    int idx = 0;
    while (idx < WatchLog->GetItemCount()) {
        wxString name = WatchLog->GetItemText(idx);
        if (name.Length() == 0) {
            WatchLog->DeleteItem(idx);
        } else {
            WatchUpdateList.Add(idx);
            idx++;
        }
    }

[compuphase]

Fixed in the latest commit of https://github.com/compuphase/Quincy.
Thank you for reporting it.

[steve64]

Many thanks, are you going to make an official release soon including the fix?
Regards,
Stefano