Changes_emlib.txt

================ Revision history ============================================
3.20.0:
 - LEUART: Added LEUART_TxDmaInEM2Enable and LEUART_RxDmaInEM2Enable for
   enabling and disabling DMA LEUART RX and Tx in EM2 support.

3.0.3:
 - Internal release for testing Wonder Gecko support.
 - SYSTEM: Added function to enable/disable FPU access on Wonder parts,
           SYSTEM_FpuAccessModeSet().
 - USART: Added USART_SpiTransfer() function.

3.0.2:
 - MSC: In MSC_WriteWord, added support for double word write cycle support
   (WDOUBLE) on devices with more than 512KiBytes of Flash memory. This can
   almost double the speed of the MSC_WriteWord function for large data sizes.
 - MSC: In MSC_ErasePage, added support for devices with Flash page size
   larger than 512 bytes, like Giant and Leopard Gecko.
 - CMU: Fixed bug in CMU_ClockDivSet. Clear HFLE and HFCORECLKLEDIV flags when
   the core runs at frequencies up to 32MHz.
 - CMU: Fixed bug in CMU_ClockEnable: Set the HFLE and HFCORECLKLEDIV flags
   when the CORE clock runs at frequencies higher than 32MHz.
 - CMU: Fixed bug in CMU_ClockSelectSet: Set HFLE and DIV4 factor for peripheral
   clock if HFCORE clock for LE is enabled and the CORE clock runs at
   frequencies higher than 32MHz.
 - BITBAND: Added BITBAND_PeripheralRead and BITBAND_SRAMRead functions.
 - DMA: Added #ifndef EXCLUDE_DEFAULT_DMA_IRQ_HANDLER around DMA_IRQHandler in
   order for the user to implement a custom IRQ handler or run without a DMA
   IRQ handler by defining EXCLUDE_DEFAULT_DMA_IRQ_HANDLER with the -D compiler
   option.
 - BURTC: In functions BURTC_Init() and BURTC_CompareSet(), moved SYNCBUSY
   loops in front of modifications of registers COMP0 and LPMODE.
 - MSC: Fixed ram_code section error on Keil toolchain.
 - MSC: Removed uneeded code from MSC init and deinit which would have no
   effect (Big thanks to Martin Schreiber for reporting this bug!).
 - System: Added access functions for reading some values out of the Device
   Information page.

3.0.1:
 - LFXO fix for Giant family.
 - USART: Fix for EFM32TG108Fxx which does not have USART0.
 - EBI: The write to the CTRL register now happens before the ROUTE registers
   are set. This avoids potential glitches.
 - LESENSE: Fix issue when using lesenseAltExMapACMP.
 - TIMER: Fix compilation on devices where ADC is not available.
 - LCD: Fix bug where Aloc field would not be set to 0.
 - BURTC: Fix Reset function by adding reset of COMP0 register and removing
   reset of POWERDOWN register. The POWERDOWN register cannot be used to
   power up the blocks after it has been powered down.
 - CMU: Fixed bug where ClockDivSet, ClockDivGet and ClockFreqGet didn't work for
   cmuClock_LCDpre clock. Also corrected 3 wrongly typed constants.
 - CMU: Fixed bug where LFBE field in LFCLKSEL was not cleared before setting
   bit-value.
 - CMU: Fixed bug with CMU_ClockSelectGet. Did not give correct return value
   for cmuClock_LFB.
 - I2C: Fixed bug where I2C_Init would set divisor depending on the previous
   master/slave configuration, not the one set in the initialization.
 - I2C: Fixed issue in the function I2C_BusFreqSet (called by I2C_Init). The
   input parameter 'I2C_ClockHLR_TypeDef type' was not in use. The fix enables
   the parameter to add support for 'i2cClockHLRAsymetric' and 'i2cClockHLRFast'
   modes. In order to use 'i2cClockHLRAsymetric' and 'i2cClockHLRFast' the
   frequency of the HFPER clock may need to be increased.
 - OPAMP: Fixed bug in the function OPAMP_Enable where an incorrect register
   was used when setting the OPA2 calibration value.
 - LEUART: Fixed issue in LEUART_BaudrateSet when a high clock frequency and a
   low baudrate can overflow the clock divisor register (CLKDIV). The fix uses
   an assert statement to check whether the calculated clock divisor is out of
   range.
 - USART: Fixed issue in USART_BaudrateAsyncSet when a high clock frequency and
   a low baudrate can overflow the clock divisor register (CLKDIV). The fix uses
   an assert statement to check whether the calculated clock divisor is out of
   range.

3.0.0:
 - efm32lib renamed emlib, as it will include support for non-EFM32 devices
   in the future
 - Added CMSIS_V3 compatibility fixes, and use of CMSIS_V3 definitions
 - See Device/Changes-EnergyMicro.txt for detailed path changes
 - New prefixes of all files, efm32_<peripherqal>.c/h to em_<peripheral>.c/h
 - New names for readme and changes files
 - RMU - BUMODERST not masked away when EM4 bits has been set
 - CMU - CMU_LFClkGet now accounts for ULFRCO bit for Tiny Gecko

2.4.1:
 - New, open source friendly license
 - Fixed BURTC initialization hang if init->enable was false
 - Fixed CMU issue with USBC and USB checks not being used correctly
 - Added CMU feature, missing TIMER3 support
 - Improved accuracy of SPI mode for USART baudrate calculation
 - Corrected USBC HFCLKNODIV setting to comply with new header file defines

2.4.0:
 - Added efm32_version.h defining software version number
 - Added BURTC support for Giant and Leopard Gecko
 - Added RMU_ResetControl for BU reset flag
 - Added some missing features to EMU for back up domain and EM4 support
 - ADC TimebaseCalc(), Giant/Leopard Gecko have max 5 bits in TIMEBASE field
 - Removed EMU Backup Power Domain threshold setings from EMU_BUPDInit, added
   EMU_BUThresRangeSet() and EMU_BUThresholdSet() API calls. Threshold values
   are factory calibrated and should not usually be overridden by the user.

2.3.2:
 - Added Tiny Gecko and Giant Gecko support in RMU for new reset causes
 - CMU_ClockFreqGet will now report correct clock rates if HFLE is set (/4)
 - Added Giant Gecko specific MSC_MassErase(), erase entire flash
 - Added Giant Gecko specific MSC_BusStrategy (inline) function
 - MSC_Init() will now configure TIMEBASE correctly according to AUXHFRCO clock
   rate for Tiny Gecko and Giant Gecko

2.3.0:
 - USART - Added USART_InitPrsTrigger to initialize USART PRS triggered
   transmissions.
 - CMU - numerous updates, now supports full clock tree of Giant/Tiny Gecko
 - CMU_ClockDivSet/Get will now use real dividend and not logarithmic values
   as earlier. Prior enumerated values have been kept for backward compatibility.
 - Added support for CMU HFLE and DIV4 factor for core clock for LE
   peripherals
 - Added support for alternate LCD segment animation range for Giant Gecko
 - Fixed bug: Don't enable VCMP low power reference until after warm up,
   allow biasprog value of 0 in VCMP_Init()
 - Added support for ALTMAP (256MB address map) in EBI_BankAddress()
 - TIMER_Init() will now reset CNT value

2.2.2:
 - Added DAC0 channel 0 and 1 to ACMP for Tiny and Giant devices
 - Fixed bug in CMU for MSC WAITSTATE configuration, leading to too high wait
   states depending on clock rate
 - Fixed bug in CMU for UART1 clock enable

2.2.1:
 - UART_Reset() and LEUART_Reset() will now reset ROUTE register as well, this
   will mean GPIO pins will not be driven after this call. Take care to ensure
   that GPIO ROUTE register is configured after calls to *UART_Init*Sync
 - Fixed problems with EFM_ASSERT when using UART in USART API
 - Added Giant Gecko support for EBI (new modes and TFT direct drive)
 - Added Giant Gecko support for CMU 2 WAIT STATES, and I2C1
 - Added Giant Gecko support for UART1 in CMU
 - Added Giant Gecko support for DMA LOOP and 2D Copy operations

2.1.0:
 - EMU_Restore will now disable HFRCO if it was not enabled when entering
   an Energy Mode
 - Run time changes only applies to Gecko devices, filter out Tiny and Giant
   for CHIP_Init();
 - Added const specificers to various initialization structures, to ensure
   they can reside in flash instead of SRAM
 - Bugfix in efm32_i2c.c, keep returning i2cTransferInProgress until done

2.0.1:
 - Changed enum OPAMP_PosSel_TypeDef. Enum value opaPosSelOpaIn changed from
   DAC_OPA0MUX_POSSEL_OPA1IN to DAC_OPA0MUX_POSSEL_OPA0INP.
 - Bugfix in efm32_lesense.h, LESENSE_ChClk_TypeDef now contains unshifted
   values, fixed the implementation in efm32_lesense.c where the bug prevented
   the sampleClk to be set to AUXHFRCO.

2.0.0:
 - USART_Init-functions now calls USART_Reset() which will also disable/reset
   interrupt
 - USART_BaudrateSyncSet() now asserts on invalid oversample configuration
 - Added initialization of parity bit in LEUART_Init()
 - Added Tiny Gecko support for CMU, ULFRCO, LESENSE clocks and continuous
   calibration
 - Added Tiny Gecko support for GPIO, EM4 pin retention and wake up support
 - Added Tiny Gecko support for I2S, SPI auto TX mode on USART
 - Added Tiny Gecko support for CACHE mesasurements for MSC module
 - Added Tiny Gecko support for LCD module (with no HIGH segment registers)
 - Added Tiny Gecko support for TIMER, PWM 2x,  (DT lock not supported)
 - Added Tiny Gecko support for LESENSE module
 - Added Tiny Gecko support for PRS input in PCNT
 - Added Tiny Gecko support for async signals in PRS, PRS_SourceAsyncSignalSet()
 - Initial support for some Giant Gecko features, where overlapping with Tiny
 - Removed LPFEN / LPFREQ support from DAC
 - Fixed comments around interrupt functions, making it clear it is bitwise
   logical or interrupt flags
 - Fixed PCNT initialization for external clock configurations, making sure
   config is synchronized at startup to 3 clocks. Note fix only works for
   >revC EFM32G devices.
 - Fixed efm32_cmu.c, EFM_ASSERT statement for LEUART clock div logic was
   inverted
 - Fixed ADC_InitScan, PRSSEL shift value corrected
 - Fixed CMU_ClockFreqGet for devices that do not have I2C
 - Fixed I2C_TransferInit for devices with more than one I2C-bus (Giant Gecko)
 - Changed ACMP_Disable() implementation, now only disables the ACMP instance
   by clearing the EN bit in the CTRL register
 - Removed ACMP_DisableNoReset() function
 - Fixed ACMP_Init(), removed automatic enabling, added new structure member
   "enaReq" for ACMP_Init_TypeDef to control, fixed the EFM_ASSERT of the
   biasprog parameter
 - Added default configuration macro ACMP_INIT_DEFAULT for ACMP_Init_TypeDef
 - Fixed ACMP_CapsenseInit(), removed automatic enabling, added new structure member
   "enaReq" for ACMP_CapsenseInit_TypeDef to control, fixed the EFM_ASSERT of
   the biasprog parameter
 - Changed the name of the default configuration macro for
   ACMP_CapsenseInit_TypeDef to ACMP_CAPSENSE_INIT_DEFAULT
 - Added RTC_Reset and RTC_CounterReset functions for RTC

1.3.0:
 - MSC is automatically enabled/disabled when using the MSC API. This saves
   power, and reduces errors due to not calling MSC_Init().
 - Added API for controlling Cortex-M3 MPU (memory protection unit)
 - Adjusted bit fields to comply with latest CMSIS release, see EFM_CMSIS
   changes file for details
 - Fixed issue with bit mask clearing in ACMP
 - Functions ACMP_Enable and ACMP_DisableNoReset added
 - Added comment about rev.C chips in PCNT, CMD_LTOPBIM not neccessary any more
 - Added missing instance validity asserts to peripherals (ACMP, LEUART, USART)
 - Fixed UART0 check in CMU_ClockFreqGet()
 - Fixed command sync for PCNT before setting TOPB value during init
 - Fixed instance validity check macro in PCNT
 - Fixed TIMER_Reset() removed write to unimplemented timer channel registers
 - Fixed EFM_ASSERT statements in ACMP, VCMP
 - General code style update: added missing curly braces, default cases, etc.

1.2.1:
 - Feature complete efm32lib, now also includes peripheral API for modules
   AES,PCNT,MSC,ACMP,VCMP,LCD,EBI
 - Fixed _TIMER_CC_CTRL_ICEDGE flags for correct timer configuration
 - Fixed ADC calibration of Single and Scan mode of operation
 - Added PCNT (ChipRev A/B PCNT0 errata NOT supported) and AES support
 - Fixed conditional inclusion in efm32_emu.h
 - Fixed code for LEUART0 for devices with multiple LEUARTs.
 - Fixed incorrect setting of DOUT for GPIO configuration

1.1.4
 - Fix for TIMER_INIT_DEFAULT

1.1.3:
 - Added ADC, DAC, LETIMER, PRS, TIMER (except DTI) support
 - Added utility for fetching chip revision (efm32_system.c/h)
 - Removed RTC instance ref in API, only one RTC will be supported
   (Affects also define in efm32_cmu.h)
 - Added default init struct macros for LEUART, USART
 - Added msbf parameter in USART synchronous init struct, USART_InitSync_TypeDef.
 - Updated reset for I2C, USART, LEUART to also reset IEN register.
 - Corrected fault in GPIO_PortOutSet()

1.1.2:
 - Corrected minor issues in EMU, EM3 mode when restoring clocks
 - Corrected RMU reset cause checking
 - Changed GPIO enumerator symbols to start with gpio (from GPIO_)
 - Changed CMU and WDOG enum typedefs to start with CMU_/WDOG_ (from cmu/wdog)
 - Added USART/UART, LEUART, DMA, I2C support

1.1.1:
 - First version including support for CMU, DBG, EMU, GPIO, RTC, WDOG