Anyone tried flashing .ulp or .cal yet?

[Omelnyk55]

If there is some feedback, I suppose it would be nice to hear it, even if flashing was not successful)

[16D]

I was flashing CVM3 with ulp and it gives some errors in answers from module but its probably arduino nano problem, i will change it to arduino nano r4 which is more powerfull and have more memory. During hearing flashing with other can logger i dont see problems

[Omelnyk55]

I only tried simulation so far, and get something like this (this is BSI):

F:/Peugeot/Modules/CALULP/BSI/DELPHI/CORSA F/9695850680.ulp
S0 (Hardware info) - Line: 1
FAMILY_MUX_CODE : 12 (BSI)
ISO_LINE : 00 (CAN)
INTERBYTE_TX : 00
INTERBYTE_RX : 00
INTER_TXRX : 01
INTER_RXTX : 01
CAL_TYPE : 82 (.ulp)
LOGICAL_MARK : 00
K_LINE_MANAGEMENT: 00
CHECKSUM2 : 5D
S1 (Identification Zone - ZI) - Line: 2
ADDRESS (16-bit) : 0000
FLASH_SIGNATURE : 0000
UNLOCK_KEY : B4E0
SUPPLIER : 13 (Delphi)
SYSTEM : B3 ()
APPLICATION : 50
SOFTWARE_VERSION : 06
SOFTWARE_EDITION : 8314
CAL_NUMBER : 96 958506 80
CHECKSUM2 : 88
Traceback (most recent call last):
File "F:\Peugeot\PyPSADiag\PyPSADiag_test_fork-main\main.py", line 482, in flashEcu
self.udsCommunication.flashEcu(ecu, flashFile)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^^^^^^^^^^^^^^^^
File "F:\Peugeot\PyPSADiag\PyPSADiag_test_fork-main\DiagnosticCommunication.py", line 555, in flashEcu
data = flashFile.getFlashLines()
File "F:\Peugeot\PyPSADiag\PyPSADiag_test_fork-main\DecodeCalUlpFile.py", line 124, in getFlashLines
if line[0] == 'S' and (line[1] == "2" or line[1] == "3"):
~~~~^^^
IndexError: string index out of range

[16D]

Send ulp file to Barracuda09, maybe he will something

[Barracuda09]

Yes I am looking at it now, it seems there are at the end of the ulp file a line with only one char.

Edit:
I should check if the line is length is more than 4 chars, now it checks if length is zero.
This will fail now

[Barracuda09]

Should be fixed with 423620e

[Omelnyk55]

Should be fixed with 423620e

Yep, this error is no longer present in simu)

[16D]

I have bsi for testing but i havent time to wire it on bench, actually it turn off after minute. I dont have synchronised key to it

[Barracuda09]

@16D Which BSI are you using on the bench?

Did you connect some jumper wires?

[Barracuda09]

This was my setup.

[Omelnyk55]

I have bsi for testing but i havent time to wire it on bench, actually it turn off after minute. I dont have synchronised key to it

I have EL3 2010ev bsi wired up, probably will try flashing it today. Just need to accept the loss in case of bricking
P.S to not let it disconnect, you need to short pins 32 and 33 in 60pin blue connector

[Barracuda09]

What kind of Arduino are you using @Omelnyk55

[16D]

I have 9830813080 EI5 with installed button to start/stop engine. IT's from 508 (R8) with keyless

[Omelnyk55]

What kind of Arduino are you using @Omelnyk55

I think it's arduino nano, the basic one. I shouldn't try flashing with nano?

[Barracuda09]

To be honest I did not try to flash an ECU myself, at any time

I know @16D has done it, but uses a Nano as well he received some mangled replies with flash counters I suspect it is because of the Nano low speed and memory.
I believe it finished succesfully in the end regarding the faults.

I have a R4 minima which is more powerful and has more memory.